MTHTrains 20-20701-1 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 49

background image

BL-2 Diesel Engine

37

If you experience poor or no smoke output when the smoke unit is on and has fluid, check

the wick to see if it has become hard, blackened, and unabsorbent around the heating

element. Remove the body as shown on page 33. Remove the smoke unit inspection

cover from the locomotive’s body. After removing the chassis and inspection cover

screws, lift the inspection plate away and inspect the wick. If it is darkly discolored and
hard, it should be replaced. When priming new wick add 40 drops.

ProtoSmoke™ Fluid

ProtoSmoke is the recommended fluid for M.T.H. products

and can be used in other manufacturers products as well.

Choose from 12 different scents: Christmas, Coal, Diesel,

Wood Burning, Coffee, Eggs & Bacon, Vanilla, Candy Cane,

Barbeque, Pipe Smoke, Cinnamon Roll, and Apple Pie

Headlight Replacement Instructions

The PS 3.0 headlights and other associated lights are small

LEDs that require a lot less power and generate a lot less

heat than incandescent bulbs, resulting in extremely long life

compared to the incandescent bulbs. The LEDs are not user
serviceable

«
...
35
36
37
38
39
...
»

Содержание 20-20701-1


















































Отзывы:

Нет отзывов

Похожие инструкции для 20-20701-1

Zlin Z-37A Cmelak

Бренд: KOR MODEL Страницы: 21

ACCUCRAFT 7/8 SCALE 7 x 12 INCH BAGNALL

Бренд: Accucraft Страницы: 8

OLD TIMBER BRIDGE

Бренд: Faller Страницы: 4

little tikes Lilly Tikes 2-in-1 Turtle Sandbox & Pool

Бренд: MGA Entertainment Страницы: 2

Бренд: Omegon Страницы: 134

Бренд: Kayoba Страницы: 21

St. Bernard Puppy

Бренд: Enabling Devices Страницы: 2

Бренд: E-FLITE Страницы: 2

380 KYLE STACY EDITION

Бренд: Goblin Страницы: 39

Бренд: Power Wheels Страницы: 32

Бренд: Jamara Страницы: 8

Бренд: POLA G Страницы: 4

Бренд: A4 Страницы: 20

Wacky Mole Clown

Бренд: Spirit Страницы: 3

Бренд: Stevens AeroModel Страницы: 4

Mercedes-Benz SLK 55 AMG

Бренд: Jamara Страницы: 4

Бренд: MODSTER Страницы: 13

Predator 60/70 SE

Бренд: Century Helicopter Products Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды