background image

8

Using a pair of pliers, insert the hairpin clip into the 
inner hole in the weld pin. Repeat on the other side. 
See Figure 4.

Figure 4

Insert post of cable ties that are on lower handle 
into the holes provided on the lower handle. The 
holes may be on the inside or outside. Pull cable 
ties tight and cut off the extra. See Figure 5 below. 

Figure 5

Attaching Starter Rope

The rope guide is already attached to the right side of 
the upper handle of your mower. See Figure 6.

With the spark plug wire disconnected and 
grounded, and with the safety key in the locked 
position, pull the starter rope up to the rope guide. 
See Figure 6. 

Slip the rope through the rope guide as shown 
below. Tighten the wing nut holding the rope guide 
to the upper handle.

Figure 6

Grass Catcher Assembly 

NOTE: Make certain the grass bag is turned right side
out before assembling (warning label will be on the
outside).

Soft Grass Bag 

Parts for soft grass bag:

1.

Front Frame       

2.

Rear Frame        

3.

Bag

Assembling soft grass bag:

Join the rear frame and front frame assembly as 
shown in Figure 7A.

Place the bag over the frame (black plastic side is 
the bottom of bag). Slip the openings in the side of 
the plastic channels on the bag over the hooks on 
the grass catcher frame.

Secure bag to frame by working the plastic 
channels on bag over frame as shown in Figure 7B. 
All of the plastic channels except the center top of 
the bag attach from the outside of bag. The center 
top of the bag attaches from inside the bag.

Figure 7

Attaching Grass Catcher

If your mower is equipped with a mulching plug, 
and it is in place on the mower, lift the rear 
discharge door and remove the rear mulching plug 
from the mower. See Figure 8.

Figure 8

NOTE:  Make sure that the cables are routed to the
outside of the handle when attaching the grass catcher.

Move hairpin clip to

this hole 

Weld 

Handle

Lower 

Pin 

Cable Tie

Post on 
Cable Tie

Wing Nut

Rope Guide

Upper Handle

Lower Handle

Recoil Starter

Blade Control 
Handle

Front

Frame

Assembly

Rear

Frame

Bag

Hook

Plastic

Channels

A

B

Rear 
Mulching 
Plug

Содержание Yard-Man 12A-449T402

























Отзывы: