background image

3

S

ection

 2 — i

mportant

 S

afe

 o

peration

 p

racticeS

Do:

1. 

Mow up and down slopes, not across. 

Exercise extreme caution when 

changing direction on slopes.

2. 

Watch for holes, ruts, bumps, rocks, or 

other hidden objects. Uneven terrain 

could overturn the machine. Tall grass 

can hide obstacles.

3. 

Use slow speed. Choose a low enough 

speed setting so that you will not have 

to stop or shift while on the slope. Tires 

may lose traction on slopes even though 

the brakes are functioning properly. 

Always keep machine in gear when 

going down slopes to take advantage of 

engine braking action.

4. 

Follow the manufacturer’s 

recommendations for wheel weights or 

counterweights to improve stability.

5. 

Use extra care with grass catchers or 

other attachments. These can change 

the stability of the machine.

6. 

Keep all movement on the slopes slow 

and gradual. Do not make sudden 

changes in speed or direction. Rapid 

engagement or braking could cause the 

front of the machine to lift and rapidly 

flip over backwards which could cause 

serious injury.

7. 

Avoid starting or stopping on a slope. 

If tires lose traction, disengage the 

blade(s) and proceed slowly straight 

down the slope.

Do Not: 

1. 

Do not turn on slopes unless necessary; 

then, turn slowly and gradually downhill, 

if possible.

2. 

Do not mow near drop-offs, ditches 

or embankments. The mower could 

suddenly turn over if a wheel is over the 

edge of a cliff, ditch, or if an edge caves 

in.

3. 

Do not try to stabilize the machine by 

putting your foot on the ground.

4. 

Do not use a grass catcher on steep 

slopes. 

5. 

Do not mow on wet grass. Reduced 

traction could cause sliding.

6. 

Do not shift to neutral and coast 

downhill. Over-speeding may cause the 

operator to lose control of the machine 

resulting in serious injury or death.

7. 

Do not tow heavy pull behind 

attachments (e.g. loaded dump cart, 

lawn roller, etc.) on slopes greater than 

5 degrees. When going down hill, the 

extra weight tends to push the tractor 

and may cause you to loose control 

(e.g. tractor may speed up, braking and 

steering ability are reduced, attachment 

may jack-knife and cause tractor to 

overturn).

Children

1. 

Tragic accidents can occur if the 

operator is not alert to the presence of 

children. Children are often attracted to 

the machine and the mowing activity. 

They do not understand the dangers. 

Never assume that children will remain 

where you last saw them.

a. 

Keep children out of the mowing 

area and in watchful care of a 

responsible adult other than the 

operator. 

b. 

Be alert and turn machine off if a 

child enters the area. 

c. 

Before and while backing, look 

behind and down for small 

children. 

d. 

Never carry children, even with 

the blade(s) shut off. They may 

fall off and be seriously injured 

or interfere with safe machine 

operation.

e. 

Use extreme care when 

approaching blind corners, 

doorways, shrubs, trees or other 

objects that may block your 

vision of a child who may run into 

the path of the machine.

f. 

To avoid back-over accidents, 

always disengage the cutting 

blade(s) before shifting into 

Reverse. If equipped, the 

“Reverse Caution Mode” should 

not be used when children or 

others are around.

g. 

Keep children away from hot or 

running engines. They can suffer 

burns from a hot muffler. 

h. 

Remove key when machine is 

unattended to   prevent 

unauthorized operation.

2. 

Never allow children under 14 years of 

age to operate this machine. Children 14 

and over should read and understand 

the instructions and safe operation 

practices in this manual and on the 

machine and should be trained and 

supervised by an adult.

Towing

1. 

Tow only with a machine that has a hitch 

designed for towing. Do not attach 

towed equipment except at the hitch 

point.

2. 

Follow the manufacturers 

recommendation for weight limits for 

towed equipment and towing on slopes.

3. 

Never allow children or others in or on 

towed equipment.

4. 

On slopes, the weight of the towed 

equipment may cause loss of traction 

and loss of control.

5. 

Always use extra caution when towing 

with a machine capable of making tight 

turns (e.g. “zero-turn” ride-on mower).  

Make wide turns to avoid jack-knifing.

6. 

Travel slowly and allow extra distance 

to stop.

7. 

Do not shift to neutral and coast 

downhill.

Service

Safe Handling of Gasoline:

1. 

To avoid personal injury or property 

damage use extreme care in handling 

gasoline. 

Gasoline is extremely 

flammable and the vapors are 

explosive. 

Serious personal injury 

can occur when gasoline is spilled on 

yourself or your clothes which can ignite.  

Wash your skin and change clothes 

immediately.

a. 

Use only an approved gasoline 

container.

b. 

Never fill containers inside a 

vehicle or on a truck or trailer bed 

with a plastic liner. Always place 

containers on the ground away 

from your vehicle before filling.

c. 

When practical, remove gas-

powered equipment from the 

truck or trailer and refuel it on 

the ground. If this is not possible, 

then refuel such equipment on a 

trailer with a portable container, 

rather than from a gasoline 

dispenser nozzle.

d. 

Keep the nozzle in contact 

with the rim of the fuel tank or 

container opening at all times 

until fueling is complete. Do not 

use a nozzle lock-open device.

e. 

Extinguish all cigarettes, cigars, 

pipes and other sources of 

ignition.

f. 

Never fuel machine indoors.

g. 

Never remove gas cap or add 

fuel while the engine is hot or 

running. Allow engine to cool 

at least two minutes before 

refueling.

h. 

Never over fill fuel tank. Fill tank 

to no more than ½ inch below 

bottom of filler neck to allow 

space for fuel expansion.

i. 

Replace gasoline cap and tighten 

securely.

j. 

If gasoline is spilled, wipe it off 

the engine and equipment. Move 

machine to another area. Wait 

5 minutes before starting the 

engine. 

k. 

To reduce fire hazards, keep 

machine free of grass, leaves, or 

other debris build-up. Clean up 

oil or fuel spillage and remove 

any fuel soaked debris.

l. 

Never store the machine or fuel 

container inside where there 

is an open flame, spark or pilot 

light as on a water heater, space 

heater, furnace, clothes dryer or 

other gas appliances. 

m.  Allow a machine to cool at least 

five minutes before storing.

General Service

1. 

Never run an engine indoors or in a 

poorly ventilated area. Engine exhaust 

contains carbon monoxide, an odorless, 

and deadly gas.

2. 

Before cleaning, repairing, or inspecting, 

make certain the blade(s) and all moving 

parts have stopped. Disconnect the 

spark plug wire and ground against the 

engine to prevent unintended starting. 

3. 

Periodically check to make sure the 

blades come to complete stop within 

approximately (5) five seconds after 

operating the blade disengagement 

control. If the blades do not stop within 

the this time frame, your machine 

should be serviced professionally by an 

authorized MTD Service Dealer.

4. 

Check brake operation frequently as 

it is subjected to wear during normal 

operation. Adjust and service as 

required.

Содержание 769-11837A









































Отзывы: