MTD 769-11837A Скачать руководство пользователя страница 12

Страница: 12 / 40

ection

3 — c

ontrolS

& o

peration

Brake Pedal (Hydro riding mowers) (E)

The brake pedal is located on the left side of the

riding mower, along the running board. Depress

the pedal all the way down to engage the disc

brake and bring the riding mower to a complete

stop.
Note: The brake pedal must be completely

depressed to start the engine. Refer to Safety

Interlock Switches for more information.

Clutch-Brake Pedal (6-speed riding

mowers) (F)

The clutch-brake pedal is located on the left side of

the lawn riding mower, along the running board.

Depress the clutch-brake pedal part way down

when slowing the riding mower by changing

speeds (refer to Speed Control Lever). Depress the

pedal all the way down to engage the disc brake

and bring the riding mower to a complete stop.
Note: The clutch-brake pedal must be completely

depressed to start the engine. Refer to Safety

Interlock Switches section.

Parking Brake Lever (Hydro riding

mower) (G)

To set the parking brake, fully depress the brake

pedal. Move the parking brake lever all the way

down and into the parking brake position. Release

the brake pedal to allow the parking brake to

engage.
To release the parking brake, depress the brake

pedal and move the parking brake lever out of the

parking brake position. Release the brake pedal.
Note: The parking brake must be set if the

operator leaves the seat with the engine running

or the engine will automatically shut OFF.

Parking Brake/Speed Control Lever

(6-speed riding mower) (H)

To set the parking brake, fully depress the clutch-

brake pedal. Move the parking brake/speed

control lever all the way down and into the parking

brake position. Release the clutch-brake pedal to

allow the parking brake to engage.
To release the parking brake, depress the clutch-

brake pedal and move the parking brake/speed

control lever out of the parking brake position into

the desired position. Release the clutch-brake pedal.
Note: The parking brake must be set if the

operator leaves the seat with the engine running

or the engine will automatically shut OFF.
The speed control lever allows you to regulate the

ground speed of the riding mower.
To use, depress the clutch-brake pedal and move

the parking brake/speed control lever out of the

parking brake notch and forward to increase the

riding mower’s ground speed. When a desired

speed has been reached, release the parking

brake/speed control lever into an appropriate

notch to maintain that speed.
To slow the riding mower’s ground speed, depress

the clutch-brake pedal and move the parking

brake/speed control lever rearward and release it

into a notch.

Shift Lever (6-speed riding mowers) (I)

The shift lever is located on the control panel just

below the seat, in the center of the riding mower.

It has three positions: FORWARD, NEUTRAL and

REVERSE. The brake pedal must be completely

depressed and the riding mower must not be in

motion when moving the shift lever.

Deck Lift Lever (J)

Found on your riding mower’s right fender, the

deck lift lever is used to change the height of

the cutting deck. To use, move the lever to the

left, then place in the notch best suited for your

application.

PTO Lever (K)

Found on the riding mower’s right fender, the PTO

lever is used to engage power to the cutting deck.

To operate, move the lever all the way forward.

Moving the lever all the way rearward into the OFF

position disengages power to the cutting deck.
Note: The PTO lever must be in the disengaged

(OFF) position when starting the engine.

Fuel Lever Indicator (If equipped) (L)

The fuel lever indicator is located below the seat

on the left hand side from the operator’s position

in the controls panel. Use this window to identify

the riding mower’s fuel needs. See Figure 4-3.

Fuel Fill Cap (M)

The fuel fill cap is located below the right side of

the seat on 30” deck models and on the engine to

the rear of the riding mower on 24” deck models.

Refer to the Assembly & Set-up section in this

manual for instructions for 30” deck models and

the Engine Operator’s Manual for 24” deck models

for fuel filling instructions.

Oil Fill Cap (N)

The oil fill cap is located under the left side of the

seat on models equipped with Briggs & Stratton

engines, the oil fill cap is located under the right

fender on all other models. Refer to the Engine

Operator’s Manual for instructions on checking

and adding oil to this riding mower.

Headlight (If equipped) (O)

The headlight is ON whenever the key is rotated out

of the STOP position. The headlight turns OFF when

the ignition key is moved to the STOP position.

Cup Holder (P)

The cup holder is located to the left of the

operator’s seat.

Transmission Bypass Rod (Not Shown)

The transmission bypass rod is located inside the

right tire on the lower right section of the frame.
When engaged, the rod opens a bypass within

the hydrostatic transmissions, which allows the

riding mower to be pushed short distances by

hand. Refer to the Assembly & Set-Up section for

instructions on using the bypass feature.

Operation

WARNING

Avoid Serious Injury or Death
•

Know location and function of all controls.

•

Remove objects which could be thrown by the blades.

•

Go up and down slopes, not across.

•

Use extra caution on slopes. Do not mow slopes greater

than 12 degrees. Avoid sudden turns. Use low speed.

•

Do not operate machine where it could tip or slip.

•

If machine stops going uphill, stop blades and back

down slowly.

•

Before leaving operator’s position, disengage blades,

engage parking brake, shut off and remove key.

•

Be sure blades and engine are stopped before placing

hands or feet near blades.

•

Keep safety devices (guards, shields, switches, etc.) in

place and working.

•

Keep bystanders away.

•

Allow machine to cool before fueling or storing.

•

Keep machine free of debris.

Read Operator’s Manual

Safety Interlock Switches

This riding mower is equipped with a safety

interlock system for the protection of the operator.

If the interlock system should ever malfunction,

do not operate the riding mower. Contact an

authorized service dealer.
•

The safety interlock system prevents the

engine from cranking or starting unless the

parking brake is engaged, and the PTO lever

is in the disengaged (OFF) position.

•

The engine will automatically shut OFF if the

operator leaves the seat before engaging

the parking brake.

•

The engine will automatically shut OFF if the

operator leaves the riding mower’s seat with

the PTO lever in the engaged (ON) position,

regardless of whether the parking brake is

engaged.

•

With the ignition key in the NORMAL

MOWING MODE/RUN position, the PTO will

automatically shut OFF if the PTO lever is

moved into the engaged (ON) position with

the shift lever in position for reverse travel.

•

The engine will automatically shut OFF if the

mulch plug, deck chute or bagger chute is

removed, regardless of whether the parking

brake is engaged or the PTO lever is in the

disengaged (OFF) position.

WARNING

Do not operate the riding mower if the safety interlock
system is malfunctioning. This system was designed for
your safety and protection.

Engaging the Parking Brake

To engage the parking brake:
1.

Fully depress the clutch-brake or brake

pedal and hold it down with your foot.

Move the parking brake lever down into the

parking brake position.

Release the clutch-brake or brake pedal to

allow the parking brake to engage.

To release the parking brake:
1.

Depress the clutch-brake or brake pedal

and move the parking brake lever out of the

parking brake position.

Содержание 769-11837A









































Результаты поиска

Содержание 769-11837A

Отзывы:

Похожие инструкции для 769-11837A

Бренды по названию

Популярные бренды

MTD 769-11837A, Руководство оператора

Результаты поиска

Содержание 769-11837A

Отзывы:

Похожие инструкции для 769-11837A

Бренды по названию

Популярные бренды