MTD 31AE6KKH731 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 28

background image

6

SECTION 2: ASSEMBLING YOUR SNOW THROWER

NOTE:

References to right or left side of the snow

thrower are determined from behind the unit in the
operating position (standing directly behind the snow
thrower, facing the handle panel).

NOTE:

This Operator’s Manual covers several

models.

Snow thrower features vary by model

. Not

all features referenced and pictured in this manual are
applicable to all snow thrower models.

IMPORTANT:

Two replacement auger shear pins and

cotter pins are included with this manual. Refer to

Augers

on page 19 for more information.

CAUTION:

Prior to operating your snow

thrower, refer to

Auger Control Test

on page 11.

Read and follow all instructions carefully and
perform all adjustments to verify your snow
thrower is operating safely and properly.

Securing the Handle

1.

Observe the lower rear area of the snow thrower to
be sure both cables are aligned with roller guides
before pivoting the handle upward.

2.

Secure the upper shift rod to the lower shift rod by
sliding the connector sleeve downward.

3.

Secure the right side of the handle by tightening the
plastic wing knob. Remove and discard any rubber
bands, if present. They are for packaging purposes
only.

4.

Secure the left side of the handle by tightening the
plastic wing knob into the eyebolt.

2

3

4

1

«
...
4
5
6
7
8
...
»

Содержание 31AE6KKH731





























Отзывы:

Нет отзывов

Похожие инструкции для 31AE6KKH731

Бренд: EarthWise Страницы: 48

Бренд: Echo Страницы: 32

Бренд: Batavia Страницы: 30

Бренд: Makita Страницы: 28

Бренд: Makita Страницы: 20

Бренд: Giant-Vac Страницы: 28

Бренд: Toro Страницы: 32

Бренд: Toro Страницы: 81

Бренд: Toro Страницы: 124

Бренд: Desa Страницы: 8

Бренд: Western Страницы: 16

Бренд: Western Страницы: 72

Бренд: Kärcher Страницы: 180

Бренд: Dacor Страницы: 12

Бренд: HSS Hire Страницы: 2

Бренд: Tennant Страницы: 402

GRIZZLY GP-1-UL

Бренд: B-Air Страницы: 6

Бренд: Parkside Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды