MTD 31AE6KKH731 страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 28

background image

20

SECTION 8: TROUBLE SHOOTING GUIDE

NOTE:

For repairs beyond the minor adjustments above, contact your local authorized service dealer.

Trouble

Possible Cause(s)

Corrective Action

Engine fails to start

Fuel tank empty, or stale fuel.

Blocked fuel line.
Choke control not in ON position
Faulty spark plug.
Ignition key not present.
Spark plug wire disconnected.
Engine not primed.

Fill tank with clean, fresh gasoline. Fuel will not last over thirty days
unless a fuel stabilizer is used.
Clean fuel line.
Move choke control to ON position
Clean, adjust gap or replace.
Insert key into ignition switch.
Connect spark plug wire.
Refer to the

Tecumseh

engine manual or

Starting the Engine

on page

10 of this manual for instructions on the engine primer.

Engine runs erratic

Unit running on CHOKE.
Blocked fuel line or stale fuel.

Water or dirt in fuel system.
Carburetor out of adjustment.

Move choke control to OFF position.
Clean fuel line; fill tank with clean fresh gasoline. Fuel will not last
over thirty days unless a fuel stabilizer is used.
Drain fuel tank. Refill with fresh fuel.
Refer to the

Tecumseh

engine manual.

Loss of power

Spark plug wire loose.
Gas cap vent hole plugged.
Exhaust port plugged.

Connect and tighten spark plug wire.
Remove ice and snow from cap. Be certain vent hole is clear.
Clean following the engine manual.

Engine overheats

Carburetor not adjusted
properly.

Refer to the

Tecumseh

engine manual packed with your unit or

have carburetor adjusted by an authorized service dealer.

Excessive vibration

Loose parts or damaged auger.

Stop engine immediately and disconnect spark plug wire. Tighten
all bolts and nuts. Make all necessary repairs. If vibration
continues, have unit serviced by an authorized service dealer.

Unit fails to propel itself Incorrect adjustment of drive

control cable.
Drive belt loose or damaged.

Adjust drive control cable.

Replace drive belt.

Unit fails to
discharge snow

Chute assembly clogged.

Foreign object lodged in auger.

Incorrect adjustment of auger
control cable.
Drive belt loose or damaged.
Shear pin(s) sheared.

Stop engine immediately. Clean chute assembly and inside of
auger housing with chute clean-out tool or stick.
Stop engine immediately. Remove object from auger with clean-out
tool or stick.
Adjust auger control cable.

Replace drive belt.
Replace shear pin(s).

«
...
18
19
20
21
22
...
»

Содержание 31AE6KKH731





























Отзывы:

Нет отзывов

Похожие инструкции для 31AE6KKH731

Бренд: FPZ Страницы: 100

RIBILAND PRBAT20

Бренд: Ribimex Страницы: 38

Бренд: JetAir Страницы: 29

Бренд: MTD Страницы: 32

Бренд: Static Clean Страницы: 4

Бренд: Worx Страницы: 32

Бренд: Toro Страницы: 16

Бренд: Yard-Man Страницы: 28

Бренд: Desa Страницы: 8

Бренд: Tomahawk Страницы: 31

Бренд: Poulan Pro Страницы: 35

Бренд: Tennant Страницы: 112

Бренд: Ventrac Страницы: 25

Бренд: AVANT Страницы: 22

Бренд: AVANT Страницы: 30

Snow Bull SGW803

Бренд: OREC America Страницы: 78

PRO RDP-SEBV20 SOLO

Бренд: Raider Страницы: 56

STARK Relax NL 3150R

Бренд: LAMETAL Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды