MTD 190-182 Скачать руководство пользователя страница 9

9

Figure 3-9

Figure 3-11

Figure 3-12

Figure 3-10

Outside of Bracket

Inner Hole

Inner holes

Upper Hole

Clevis Pin

Support
Bracket

Self tap

screws

Assembling Support 

Brackets

Model Series 00

1.  Locate the four self-tapping screws supplied in your 

hardware pack (B from Fig. 2-2).  Attach the right 
hand grass catcher support bracket (F1 from Fig. 
2-2) using two of the supplied screws in position as 
shown in Fig. 3-9.  Place the left hand grass catcher 
support bracket (F2 from Fig. 2-2) in position and 
secure with the other two screws.

2.  Insert a shoulder bolt (C in Fig. 2-2) through the 

Inner hole (closest to the frame) on the outside of 
the support bracket. Secure with a nut (A in Fig. 2-2). 
See Fig. 3-9 for details. Repeat on other side.

NOTE: 

If the grass collection system is removed for 

any reason, it is not necessary to remove the support 
brackets from the tractor.

Attaching The Bracket 

Assembly

1.  Remove the two nuts and screws on each side of the 

mounting bracket holding the hitch plate.   
See Fig. 3-10.

2.  Rotate the hitch plate 180° from its original position. 

Re-insert the four bolts through mounting bracket 
and hitch plate frame and secure with nuts removed 
earlier. Use the inner holes (closest to the mounting 
hooks) on the mounting bracket. Refer to Fig. 3-11.

3.  Remove the hairpin clip and clevis pin from the hitch 

plate as seen in Fig. 3-10. Save the hardware.

4.  Position the hooked ends of the mounting bracket 

assembly to the outside of the support bracket and 
over the shoulder bolts on both sides.  Refer back to 
Fig. 3-7 for reference.

5.  Reinsert the clevis pin through the aligned holes in 

both the bracket assembly and the hitch plate and 
secure with the hairpin clip removed earlier.  See Fig. 
3-12.

IMPORTANT:  There are two holes in the clevis pin. 
Be sure to insert the hairpin clip in the upper hole to 
properly secure the bracket assembly to the hitch plate.

Attaching 

Support 

Bracket & 

Bracket 

Assembly

Model Series 700

NOTE: 

 

If the grass collection 

system is removed for 

any reason, it is not 

necessary to remove the 

support brackets from the 

tractor.

IMPORTANT: 

There are two holes in 
the clevis pin. Be sure 

to insert the hairpin 

clip in the upper hole 

to properly secure the 

bracket assembly to the 

hitch plate.

Содержание 190-182





























Отзывы: