MSE SONIPREP 150 Скачать руководство пользователя страница 11

Страница: 11 / 24

INTRODUCTION

1.2

Control Panel Description
The control panel is situated on the right hand side of the unit. A brief

description of their individual functions follows:
Amplitude Meter - The meter is calibrated in microns and monitors the probe

amplitude, that is, the actual movement peak-to-peak that is taking place at the

transducer/probe interface. Multiplying the meter indication by the

transformation ratio of the particular probe in use (See Table 1) allows actual

movement of the probe tip to be determined.
Power Control - Clockwise rotation of the power control increases the

amplitude level displayed on the amplitude meter. This control permits stepless

selection of power output to the transducer, providing an accurate and

reproducible amplitude setting for the particular probe in use.
Timer - This is a 15 minute timing unit with switching contacts and a resetting or

cancellation facility. It operates independently of the start switch after the output

level has been determined, the time required is selected. The operating lamp

will be illuminated, ultrasonication will commence and the timer will start run-

down to zero. When the time selected has run the unit will switch off

automatically and the operating lamp will go off.
Override Switch - When pressed ‘ON’, allows the unit to operate continuously

regardless of the time set.
Operating Lamp - When illuminated, indicates that the power is through to the

transducer.

Содержание SONIPREP 150

























Результаты поиска

Содержание SONIPREP 150

Отзывы:

Бренды по названию

Популярные бренды

MSE SONIPREP 150, Инструкция по эксплуатации

Результаты поиска

Содержание SONIPREP 150

Отзывы:

Бренды по названию

Популярные бренды