MSD Atomic LS EFI 2950 Скачать руководство пользователя страница 6

Страница: 6 / 21

INSTALLATION INSTRUCTIONS

INSTALLING THE INTEGRATED FUEL/ECU RAILS

The integrated fuel/ECU rails are supplied with the covers installed. The rails are designed to install to OEM

intake manifolds and many aftermarket designs. To prepare the rails for installation, locate the four intake

manifold bolts supplied with the Atomic LS Master Kit, as well as the four mounting brackets.
It is important to note at this point, that you have the correct injectors for your application as well as O-ring

seals and the injector retainers. These components are not supplied in the master kit.

WARNING:

Care must be used when installing the fuel injectors and rail assemblies.

The following steps will guide you

through the installation of the two fuel

rail assemblies.

1. The fuel rails are supplied with

the covers in place. Remove the

covers to prepare and install the

rail assemblies (Figure 3). Also,

determine which rail is which by

reviewing the sensor connectors

and location as shown in Figure 9

on page 8.

2. Figure 4 shows the location for the fuel

rail brackets. Remove the hardware

from the intake manifold and install

the brackets as shown using the

supplied longer intake bolts. Use

GM 1245383 thread sealant or

equivalent on the intake manifold

bolts. Note that the passenger rear

bracket requires a spacer (supplied)

as shown in Figure 4. Torque the new

intake bolts to 89 in-lbs.

NOTE:

If installing the intake manifold

for the first time follow the

torque sequence in Figure

4. Torque in steps; 44 in-lbs

first, followed by 89 in-lbs.

It is recommended to hold

a straight edge against the

brackets to ensure alignment

while torquing.

Figure 4 Fuel Rail Bracket Locations.

Figure 3 Removing Fuel Rail Covers.

REAR

FRONT

BRACKET

NOTE: THE PASSENGER

SIDE REAR MOUNT

REQUIRES THE

SUPPLIED SPACER.

TORQUE SEQUENCE

STEP 1 - 44 LBS/INCH

STEP 2 - 89 LBS/INCH

FUEL RAIL

COVER

LIFT THIS SIDE OF

COVER ENOUGH TO

CLEAR FUEL RAIL

FUEL RAIL

COVER

PUSH COVER

FUEL RAIL

COVER

LIFT COVER UP

DISENGAGE

FROM FUEL

RAIL

MUST USE THREAD SEALANT

Содержание Atomic LS EFI 2950






















Результаты поиска

Содержание Atomic LS EFI 2950

Отзывы:

Похожие инструкции для Atomic LS EFI 2950

Бренды по названию

Популярные бренды

MSD Atomic LS EFI 2950, Руководство по установке

Результаты поиска

Содержание Atomic LS EFI 2950

Отзывы:

Похожие инструкции для Atomic LS EFI 2950

Бренды по названию

Популярные бренды