MSA NightFighter Скачать руководство пользователя страница 6

Страница: 6 / 15

ManualNightFighterInstallation.doc

Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02

Page 6 of 15

5. Verify that there is no loose play in the assembly of parts.

6. Don the facepiece and check the face-to- facepiece seal. Follow the Facepiece Fit Check

procedures in the MMR with Slide Connection Operation and Instructions Manual.

Installing the Component Housing Cover Adapter Assembly for BMR

1. Place the component housing cover over the housing.

2. Insert the tab on the top of the cover into the slot in the bottom of the lens ring.

3. Press in on the front of the cover until the cover hook snaps into place.

4. Line up the screw holes in the cover with the metal tab of mounting bracket and threaded

inserts in the housing.

5. Place the neckstrap retaining brackets in the component housing cover sockets. Install the

Phillips screws and tighten to secure the housing and neckstrap.

6. Insert the adapter assembly in the facepiece and hand-tighten.

7. Don the facepiece and check the face-to- facepiece seal. Follow the Facepiece Fit Check

procedures in the BMR Operations and Instructions Manual.

Содержание NightFighter















