background image

TAL 709 (L) Rev. 4

© MSA 2007

Prnt. Spec. 10000005389(A)

Mat. 10058881

Doc. 10000020525

Use of this device must be consistent with the requirements of NFPA 1500 Fire Department Occupational Safety
and Health Programs.

The Nightfighter Heads-Up Display System is NIOSH certified as an accessory for the Ultra Elite Facepiece for use
with the MSA MMR, Firehawk MMR, and BMR breathing apparatus only.

The warranties made by MSA with respect to the product are voided if the product is not installed, used and ser-
viced in accordance with the instructions in this manual. Please protect yourself and your employees by following
the instructions. Please read and observe the WARNINGS and CAUTIONS inside. For any additional information
relative to use or repair, write or call 1-800-MSA-2222 during regular working hours.

Read this manual carefully if you have or will have the responsibility for using or servicing the product. These
instructions pertain only to the use of the version of the ICM Tx Unit and NightFighter Heads-Up Display System
which integrates with the SCBA. These instructions, in addition to the instructions supplied with the SCBA, must
be carefully read and followed by all persons who use or maintain this product. This includes those who have
any responsibility involving its selection or application. The ICM Tx Unit and NightFighter from MSA will per-
form as designed only if used and maintained according to the instructions. Otherwise it could fail to perform
as designed and persons who rely on the SCBA could sustain serious personal injury or death.

ICM

®

Tx Unit and

NightFighter

®

Heads-Up Display
System

NOTICE

These instructions must remain attached to the ICM Tx Unit or Nightfighter Heads-Up Display System. The end
user only is authorized to remove them from the device.

OPERATION AND MAINTENANCE INSTRUCTIONS

The Nightfighter Heads-Up Display System and ICM Tx Unit comply with Part 15 of the FCC Rules. Operation is
subject to the following conditions:
(1) This device may not cause harmful interference and (2) This device must accept any interference that may
cause undesired operation.

Changes and modifications not expressly approved by the manufacturer could void the user’s authority to oper-
ate the equipment.

Содержание ICM Tx

























Отзывы: