manualshive.com logo in svg

MSA fieldserver EZ Gateway M-Bus to Modbus & BACnet, Руководство для стартапов

Поделиться
Скачать
MSA fieldserver EZ Gateway M-Bus to Modbus & BACnet Скачать руководство пользователя страница 41

Troubleshooting 

 
 
 

 

 EZ Gateway Start-up Guide 

41 

 
 

8.2.1  Taking a Capture with Older Firmware  

If  the  FieldServer  firmware  is  from  before  November  2017,  the  Diagnostic  Capture  can  be  done  by 
downloading  the  FieldServer  Toolbox  software  but  network  connections  (such  as  Ethernet  and  Wi-Fi) 
cannot be captured (if a network diagnostic is needed take a Wire Shark capture).

 

Once the Diagnostic Capture is complete, email it to technical support. The Diagnostic Capture will 
accelerate diagnosis of the problem. 

NOTE:  While all necessary documentation is shipped with the FieldServer on the USB flash drive, 

these documents are constantly being updated. Newer versions may be available on the 
MSA Safety website.

 

•

 

Ensure  that  FieldServer  Toolbox  is  loaded  onto  the  local  PC.  Otherwise,  download  the 
FieldServer-Toolbox.zip via the MSA Safety website.

 

•

 

Extract the executable file and complete the installation.

 

 

 

•

 

Connect a standard Cat-5 Ethernet cable between the PC and EZ Gateway. 

 

•

 

Double click on the FS Toolbox Utility. 

•

 

Step 1:

 Take a Log 

o

  Click on the diagnose icon           of the desired device 

 

Figure 48: Ethernet Port Location 

Ethernet Port 

Содержание fieldserver EZ Gateway M-Bus to Modbus & BACnet
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды