MS Sedco TDM Скачать руководство пользователя страница 6

Page 6

(82A044)  TDMv1017

FIGURE 5—Operation Display & Additional Programming Options

When the unit is operating, the display will indicate which output is active for the duration of its 

programmed time delay.  For relay output #1, a 

1

 will be displayed and 

2

 will be displayed for relay output 

#2.  If the delays d3 or d4 are used (such as an installation using a Mag Lock or a Vestibule application), 

the delay will be evident between the displaying of both outputs.

In addition to the settings already described in the previous sections, below is a listing of various options 

which are programmable on the TDM.  The LED display vs. function are as follows:

––

 = Ready Mode (flashing)

d1

 = Time Delay or "ON TIME" of relay output #1—0.0 to 99 seconds

d2

 = Time Delay or "ON TIME" of relay output #2—0.0 to 99 seconds

d3

 = Time Delay between d1 and d2—0.0 to 99 seconds

d4

 = Time Delay between d2 and d1—0.0 to 99 seconds

i1

 = Switch Input #1—(N.O. or N.C.)

i2

 = Switch Input #2—(N.O. or N.C.)

i3

 = Switch Input #3—(N.O. or N.C.)

i4

 = Switch Input #4—(N.O. or N.C.)

o1

 = Relay Output #1—(N.O. or N.C.)

o2

 = Relay Output #2—(N.O. or N.C.)

- -

 = Error (flashing)

The 

PUSHBUTTON FAULT INDICATOR

 is a special feature designed to alert the installer if a pushbutton is 

"stuck" in the active position or if the wires have shorted.  If this occurs, the display will flash double dots 

(

 

.

 

.

 

).  Additionally, this could mean that the wiring did not match the programmed parameter.  In other 

words, the unit may be programmed for use with a normally open switch, but may be wired to a normally 

closed switch.  Normal operation will resume once the fault condition has been cleared.

WET/DRY CONTACT OPTION:

The TDM has the option of supplying power to relay output #1 contacts.  This is known as "WET" contacts 

instead of the conventional "DRY" contacts or simple contact closure.  Providing this voltage can simplify 

the wiring of installations where an Electric Locking  device is used.  However, the voltage supplied to the 

output is the same voltage supplied to the input of the TDM and must be compatible with the Locking 

device to be controlled.  Please contact the factory for additional information.

                             Universal Time Delay Module 

INSTALLATION INSTRUCTIONS

The 

Commander

Series

TDM

7898 Zionsville Road 

 Indianapolis, Indiana 46268

Telephone: (317) 842-2545 

 www.mssedco.com 

 [email protected]

Содержание TDM







Отзывы: