MS Sedco TDM Скачать руководство пользователя страница 4

Page 4

(82A044)  TDMv1017

FIGURE 3—Electric Lock and Door Operator

Once the TDM has been wired for the above application, programming of the device is as follows:
1)  Apply power to the unit.  The display will flash double bars (

––

) indicating that the unit is in its normal 

 

operating ready mode.

2)  To begin programming, depress the 

PROGRAM MODE BUTTON

 one time.  The first parameter to be 

 

programmed will appear on the display.  This is the delay time, or "on time" of the output #1 and is 

 

displayed as 

d1

 followed by the time setting of 

2.0

 (Factory Setting) which indicates 2.0 seconds (It will 

 

flash between the two).  This is the time duration that you want the Electric Lock released (It's usually 

 

set around 2-3 seconds).  To adjust the time setting, use a small screwdriver and rotate the 

DISPLAY 

 ADJUSTMENT 

clockwise to increase and counterclockwise to decrease the time setting.  After the 

 

desired value is displayed, depress the 

PROGRAM MODE BUTTON

 again to save the value.  The 

 

display will now read 

d2

.  

d2

 is the delay time or "on time" of output #2.  This is the time setting that 

 

you want for the door (operator) to remain open.  This is usually set around 3-5 seconds.  To adjust the 

 

setting, rotate the 

DISPLAY ADJUSTMENT

 until the desired value is displayed and then depress the 

 

PROGRAM MODE BUTTON

.  The display should then read 

d3

.  This is the setting for the delay time 

 

between the release of the Electric Lock and the opening of the door.  This time is usually set around 

 

0.5-1 second.  Again, adjust the setting and then depress the 

PROGRAM MODE BUTTON

.  The display 

 

should now read 

d4

.  Now wait 30 seconds until the double bars (

––

) appear, indicating that the unit is 

 

in its normal operating ready mode.  

*NOTE: d1 should be longer than d3.

3)  You are now ready to test your installation.  If any of the time settings need to be changed, make the 

 

change and press the 

PROGRAM MODE BUTTON

 once to save the new value.  Then wait 30 seconds 

 

until the double bars (

––

) appear again, indicating that the unit is in its normal operating mode.

4)  During operation of the unit, the display will indicate its operating status.  Please refer to Figure 5 at 

 

the end of this installation manual.

Wall

Switch

PUSH

TO 

OPEN

MS SEDCO

TDM

Timing Control Module

12-24V

AC / DC

12-24V

Magnetic

or Electric Exit Device

Lock

Door

Operator

Control

N.O.

N.C.

Output #1

input #1

Output #2

GRAY

VIO

BLU

WHT / BLU

BROWN

YEL

GRN

GRN

Jumper installed for 

   "DRY" contacts

TDM

INPUT 

4

INPUT 

3

INPUT 

2

INPUT 

1

12-24V AC/DC

INPUT 

1

COM

COM

COM

COM

N.

O.

N.

C.

N.

C.

N.

O.

PROGRAM

MODE BUTTON

DISPLAY

ADJUSTMENT

LED DISPLAY KEY

d1 = delay 1

d2 = delay 2

d3 = delay d1 to d2

d4 = delay d2 to d1

i1 = input 1 (n.o. / n.c.)

i3 = input 3 (n.o. / n.c.)

i2 = input 2 (n.o. / n.c.)

i4 = input 4 (n.o. / n.c.)

o2 = output 2 (n.o. / n.c.)

o1 = output 1 (n.o. / n.c.)

o1= dry

o1= wet

Output #1

Output #2

PROGRAMMING 

PROCEDURE

NOTE:

  Mag Lock uses N.C. 

  (Gray & Violet)

 

  Electric Exit device uses 

  N.O. (Gray & White)

                             Universal Time Delay Module 

INSTALLATION INSTRUCTIONS

The 

Series

TDM

Commander

7898 Zionsville Road 

 Indianapolis, Indiana 46268

Telephone: (317) 842-2545 

 www.mssedco.com 

 [email protected]

Содержание TDM







Отзывы: