MS Sedco TDM Скачать руководство пользователя страница 3

Page 3

(82A044)  TDMv1017

FIGURE 2—Simple Time Delayed Output

Once the TDM has been wired for the above application, programming of the device is as follows:

1)  Apply power to the unit, provided there is no smoke or fire, you can assume that your wiring job must 

 

be somewhat successful.

2)  Once properly powered, the display will flash double bars (

––

) indicating that the unit is in its normal 

 

operating ready mode.

3)  To begin programming, depress the 

PROGRAM MODE BUTTON

 one time.  The first parameter to be 

 

programmed will appear on the display.  This is the delay time, or "on time" of the output #1 and is 

 

displayed as 

d1

 followed by the time setting (It will flash between the two).  To adjust the time setting, 

 

use a small screwdriver and rotate the 

DISPLAY ADJUSTMENT

 clockwise to increase and 

 

counterclockwise to decrease the time setting.  After the desired value is displayed, depress the 

 

PROGRAM MODE BUTTON

 again to save the value.  The display will now read 

d2

.  Now wait 30 

 

seconds until the display again reads double bars (

––

) indicating that the unit is in its normal 

 

operating ready mode.

4)  You are now ready to test your installation.  If the time delay has to be changed, make the change to 

 the 

d1

 setting, press the 

PROGRAM MODE BUTTON

 once and then wait 30 seconds until the double 

 

bars (

––

) appear again.

5)  During operation of the unit, the display will indicate its operating status.  Please refer to Figure 5 at 

 

the end of this installation manual.

or Electric Exit Device

Wall

Switch

PUSH

TO 

OPEN

WHT/RED

WHT/VIO

MS SEDCO

TDM

Timing Control Module

N.C.

Output #1

Input #3

SPRINKLER

OR FIRE

DETECTION

SYSTEM

(IF USED)

FIRE

SYSTEM

(IF USED)

PROTECTION

SIGNALING

Mag Lock

N.C.

N.C.

AC / DC

GRN

GRN

GRAY

VIO

JUMPER

INSTALLED 

FOR "DRY"

CONTACTS

12-24V

12-24V

This separate power source ( & associated wiring) can be eliminated 

if the jumper is set for "WET" contacts instead of "DRY" contacts.

(see page 6)

TDM

INPUT 

4

INPUT 

3

INPUT 

2

INPUT 

1

12-24V AC/DC

INPUT 

1

COM

COM

COM

COM

N.

O.

N.

C.

N.

C.

N.

O.

PROGRAM

MODE BUTTON

DISPLAY

ADJUSTMENT

LED DISPLAY KEY

d1 = delay 1

d2 = delay 2

d3 = delay d1 to d2

d4 = delay d2 to d1

i1 = input 1 (n.o. / n.c.)

i3 = input 3 (n.o. / n.c.)

i2 = input 2 (n.o. / n.c.)

i4 = input 4 (n.o. / n.c.)

o2 = output 2 (n.o. / n.c.)

o1 = output 1 (n.o. / n.c.)

o1= dr

y

o1= wet

Output #1

Output #2

PROGRAMMING 

PROCEDURE

NOTE:

  Mag Lock uses N.C. 

  (Gray & Violet)

 

  Electric Exit device uses 

  N.O. (Gray & White)

                             Universal Time Delay Module 

INSTALLATION INSTRUCTIONS

The 

Series

TDM

Commander

7898 Zionsville Road 

 Indianapolis, Indiana 46268

Telephone: (317) 842-2545 

 www.mssedco.com 

 [email protected]

Содержание TDM







Отзывы: