background image

 

OPERATING MANUAL OXYGEN MONITORING SYSTEM   

OMS 420

 

 

33

 

9.7.5

 

O2 cell setup (by factory only) 

If there is no calibration gas available and the cell must be replaced, this function permits changing a cell without calibration. This 
can only be done if the cell factors have been measured at MRU and delivered together with the spare sensor. 

 

  

  

  

  

  

  

 

PREV or NEXT 

move cursor 

EDIT 

 

change value by means of UP/DOWN and POS 

OK  

save 

values 

BACK 

 

return to calibration menu

 

1) 

O2 cell setup requires input (edit function) of O2 factor and O2 offset values delivered with the spare sensor 

2) 

Temperature compensation of  20.9 % O

2

 is required when oxygen value at air is changed too much because of gas or 

flange temperature change. The difference of air oxygen measurement at lower temperature to measurement at higher tempera-
ture will be edit as “Temp.offs” value. 

NOTE: 

This procedure should be followed by new calibration using calibration gas cylinder.  

Only authorized persons or manufacturer’s trained technicians are authorized to perform adjustments on the OMS420. 

 

9.7.6

 

CO cell setup (by factory only) 

If there is no calibration gas available and the cell must be replaced, this function permits changing a cell without calibration. This 
can only be done if the cell factors have been measured at MRU and delivered together with the spare sensor. 

 

 

 

   

PREV or NEXT 

 

move cursor 

EDIT 

 

 

change value by means of UP/DOWN and POS 

OK 

  save 

values 

BACK 

 

 

return to calibration menu

 

CO cell setup factor and CO offset setup factor will be edit using the values delivered together with the spare sensor.  

 

Set point of heat resistor [Ohm] must be also carried out according to § 6.7.12 
NOTE: 

This procedure should be followed by new calibration using calibration gas cylinder.  

Only authorized persons or manufacturers trained staff are allowed to perform adjustments on the OMS420!

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание OMS 420












































Отзывы: