background image

Introduction

Thank you for purchasing MRC’s Prodigy Advance

2  

DCC (Digital

Command Control) system. You now own one of the most advanced,

easy to use DCC systems available. It comes as a complete system with

a Command Station (base unit), power supply and LCD Cab/Handheld

with cable. The MRC Prodigy Advance DCC

system will enhance the

enjoyment of your train layout for many years to come. Here at MRC, we

pride ourselves in giving you the most advanced, reliable and easy to use

DCC train controls. With up to 9,999 addresses available and use of up to

99 Cabs, you can expand your railroad empire as much as you desire.

From a beginner’s 4x8 layout to a massive club layout, the Prodigy

Advance

2

 gives you everything you want.

Note

Although there are Quick-start instructions on the back of the Cab/

Handheld, please read these instructions thoroughly to better

understand and enjoy your Prodigy Advance

2

 DCC system.

DCC Basic Background

A DCC system consists of a DCC Command Station that sends DCC

commands to your layout and DCC decoders installed in your locos that

receive the DCC commands. Each decoder equipped loco has its own

address. Each decoder receives DCC commands but only follows those

commands matching its address. No more multiple blocks and no more

multiple power packs. With DCC, you can run different locos with different

speeds and directions all on the same track. You can also turn on/off the

loco’s headlight and activate sounds if your loco is equipped with a sound

decoder. Please visit our website at 

www.modelrectifier.com

 for more

information about other DCC products.
Please read this manual 

and 

your decoder manual carefully before

installing and operating your DCC system.

Note 

The Prodigy Advance

2

 does not support NON-decoder equipped or analog

locos. MRC’s earlier DCC systems do support running analog locos.

However, running analog locos will dramatically slow the response time of

your DCC system. Therefore, our new Prodigy Advance does not support

this old feature.

Info

For more information on DCC or Prodigy Advance

2

, visit the Resources

section of our web site at www.modelrectifier.com or visit the

National Model Railroad Association’s website at www.nmra.org.

1

Getting Started

MRC Prodigy Advance

2

Getting Started  1-1

Содержание 0001414





















Отзывы: