background image

Controlling Accessory Functions

To control accessory functions F1 - F9,

press 

-

 9

. To control F10 - F28, press

SHIFT

, then press 2 digits. When F1-

F12 are on, F1 - F12

 

will be displayed

on the LCD. F13 - F19 will not be

displayed.
The left LCD display shows that the

current loco is 3802 running in reverse

at a speed of 102. Its accessory

functions F1 and F11 are on.

Recalling Locos

To call up previous locos stored in the memory, press 

RECALL

. You can

recall up to 25 locos.

Note

Although the Cab can store up to 25 locos, if you unplug the Cab from the

base unit, it will only retain the last 5 locos used.

Deleting Locos

The Cab can store up to 25 locos. If you select a new loco when the Cab is

full, the new loco will replace the current loco. The current loco will be lost.

To prevent this, we recommend you recall unused locos and delete them

by pressing and holding 

DEL

 for 2 seconds.

Emergency Stopping

For emergency stopping of the current loco, press 

STOP.

 Pressing and

holding 

STOP

 for 2 seconds will stop the Main Track output. The 2 lights

on the base unit will blink. To restore the Main Track output, press and hold

STOP

 for 2 seconds again.

Speed Steps

Speed steps are incremental steps the loco takes to go from 0 to top

speed. There are three speed steps: 14, 28 and 128. The higher the speed

steps setting, the higher the number of different speeds on which the loco

can operate. When you enter a new loco address (an address that has not

been stored in the Cab’s memory), Prodigy Advance will set 28 speed

steps as the default setting for that address. In order to operate your loco

properly, you may need to change the speed steps setting to match the

decoder’s speed steps.
To select other speed steps settings, press 

SPD STEP

 repeatedly until you

see your desired speed steps setting. Then press 

ENTER

. The selected

speed steps setting will apply only to that address.

Note

Use of the speed step button will not alter the speed step originally

programmed into the decoder. It only matches the throttle to the decoder.

Yard Mode On/Off

To toggle the Yard Mode feature on or off, press 

SYS

 and 

3

. In standard

throttle mode, the throttle only controls loco speed. When the Yard Mode

feature is on (“Yard” displayed on LCD), the yard throttle will control both

the speed 

and 

direction of the loco. Let’s explain how to use the Yard

throttle.
When the loco is traveling forward, turning the yard throttle clockwise will

increase the loco’s speed. Turning counterclockwise will decrease its

F1

Loco

REV

H

Speed

F11

2-2  Operation

MRC Prodigy Advance

2

Содержание 0001414





















Отзывы: