manualshive.com logo in svg

MR VACUTAP VV I 145kV, Руководство по эксплуатации

Поделиться
Скачать
MR VACUTAP VV I 145kV Скачать руководство пользователя страница 48

7 Maintenance

Maschinenfabrik Reinhausen GmbH 2020

48

4349312/01 EN

VACUTAP

®

 VV

®

A label on the inside of the door of the TAPMOTION® ED motor-drive unit
also specifies the relevant maintenance interval.

Figure 21: Label showing maintenance intervals

Maintenance intervals with MR monitoring system

 WARNING

Danger of explosion!

If pending maintenance work is not carried out immediately, this may lead to
death or serious injury as a result of a progressive short circuit, for example.

► Contact the Maschinenfabrik Reinhausen GmbH Technical Service de-

partment as soon as the MR monitoring system issues a maintenance
warning.

► In the event of failure or shutdown of the MR monitoring system, observe

the maintenance intervals as specified in the maintenance plan without
the MR monitoring system.

If you are operating the on-load tap-changer with an MR monitoring system,
the maintenance intervals displayed by the MR monitoring system shall ap-
ply. More information can be found in the operating instructions for the MR
monitoring system.

Содержание VACUTAP VV I 145kV

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды