MQ Power DCA300SSC WHISPERWATT SERIES Скачать руководство пользователя | Manualshive

Страница: 34 / 92

background image

PAGE 34 — DCA300SSC GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (06/25/09)

GENERATOR START-UP PROCEDURE (MANUAL)

BEFORE STARTING

Place the

1.

main, G.F.C.I., and aux.

circuit breakers (

Figure

35

) in the

OFF

position prior to starting the engine.

Main, Aux. and GFCI

Figure 35.

Circuit Breakers (OFF)

Make sure the

2.

voltage change-over board

has been

confi gured for the desired output voltage.

Connect the load to the

3.

receptacles

or the

output

terminal lugs

as shown in Figure 10. These load

connection points can be found on the output terminal
panel and the output terminal panel’s hard wire hookup
panel.

Tighten terminal nuts securely to prevent load wires

4.

from slipping out.

Close all engine enclosure doors (Figure 36).

5.

Engine Enclosure Doors

Figure 36.

CAUTION

The engine’s exhaust contains harmful emissions.

ALWAYS have adequate ventilation

when operating.

Direct exhaust away from nearby personnel.

WARNING

NEVER

manually start the engine with the

main, GFCI or

auxiliary

circuit breakers in the

ON

(closed) position.

INCORRECT

CORRECT

STARTING (MANUAL)

Place the engine speed switch (Figure 37) in the LOW

1.

(down) position.

Engine Speed Switch (Low)

Figure 37.

Place the

2.

MPEC control switch

in the

MANUAL

position to start the engine (Figure 38).

MPEC Control Switch

Figure 38.

(Manual Position)

Depending on the temperature of the coolant (cold

3.

weather conditions), the pre-heat lamp (Figure 39) will
light (ON) and remain on until the pre-heating cycle has
been completed. After completion of the pre-heating
cycle, the light will go OFF and the engine will start up
automatically.

Pre-Heat Button

Figure 39.

Once the engine starts, let the engine run for 1-2

4.

minutes. Listen for any abnormal noises. If any
abnormalities exist, shut down the engine and correct
the problem. If the engine is running smoothly, place
the engine speed switch (Figure 40) in the

HIGH

(up)

position.

Engine Speed Switch (High)

Figure 40.

Verify that the

5.

engine running

status LED on the MPEC unit
(Figure 41) is

ON

(lit) after the

engine has been started.

Engine Running LED (ON)

Figure 41.

«
...
32
33
34
35
36
...
»

Содержание DCA300SSC WHISPERWATT SERIES





























































































Отзывы:

Нет отзывов

Похожие инструкции для DCA300SSC WHISPERWATT SERIES

Бренд: bem wireless Страницы: 5

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 5

Бренд: G-project Страницы: 14

Бренд: Kodiak Страницы: 40

Бренд: Fortin Страницы: 4

Бренд: Xoro Страницы: 122

Бренд: Generac Power Systems Страницы: 2

Бренд: Wiltron Страницы: 160

GP Series 005938-0

Бренд: Generac Power Systems Страницы: 56

Бренд: Soga Страницы: 28

Бренд: Shindaiwa Страницы: 54

Бренд: Sytech Страницы: 4

Бренд: Bluetti Страницы: 28

Бренд: Wanco Страницы: 18

Super Slim Portable Stereo Speaker

Бренд: Jumbl Страницы: 1

Бренд: Infinity Страницы: 8

Бренд: Kemppi Страницы: 20

Бренд: Wallenstein Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды