MQ Power DCA300SSC WHISPERWATT SERIES Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 92

background image

DCA300SSC GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (06/25/09) — PAGE 39

MAINTENANCE

If the engine is operating in very

dusty

or

dry grass

conditions, a clogged air cleaner will result. This can lead to
a loss of power, excessive carbon buildup in the combustion
chamber and high fuel consumption. Change air cleaner
more

frequently

if these conditions exists.

FUEL ADDITION

Add diesel fuel (the grade may vary according to season
and locations).

Removing Water from the Fuel Tank

After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally inspect the fuel
tank for water contamination and drain the contents if
required.

During cold weather, the more empty volume inside the
tank, the easier it is for water to condense. This can be
reduced by keeping the tank full with diesel fuel.

Cleaning Inside the Fuel Tank

Drain the fuel inside the fuel tank completely. Using a spray
washer (Figure 57) wash out any deposits or debris that
have accumulated inside the fuel tank.

Fuel Tank Cleaning

Figure 57.

FUEL TANK INSPECTION

In addition to cleaning the fuel tank, the following
components should be inspected for wear:

Rubber Suspension



— look for signs of wear or

deformity due to contact with oil. Replace the rubber
suspension if necessary.

Fuel Hoses



— inspect nylon and rubber hoses for signs

of wear, deterioration and hardening.

Fuel Tank Lining



— inspect the fuel tank lining for signs

of excessive amounts of oil or other foreign matter.

Replacing Fuel Filter

Replace the fuel fi lter cartridge with new one every 500



hours or so.

Loosen the drain plug at the lower top of the fuel fi lter.



Drain the fuel in the fuel body together with the mixed
water.

DO NOT

spill the fuel during disassembly.

Vent any air



AIR REMOVAL

If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel,
or after disassembling the fuel system, bleed the system
according to the following procedure. See the

Cummins

Engine Manual

for details.

«
...
37
38
39
40
41
...
»

Содержание DCA300SSC WHISPERWATT SERIES





























































































Отзывы:

Нет отзывов

Похожие инструкции для DCA300SSC WHISPERWATT SERIES

Бренд: Samsung Страницы: 32

Бренд: Samsung Страницы: 32

Бренд: Baofeng Страницы: 7

MPD820 - DVD Player - 8

Бренд: Magnavox Страницы: 42

Бренд: Pulsar Страницы: 39

Бренд: Briggs & Stratton Страницы: 5

Бренд: Fresh 'N Rebel Страницы: 34

Бренд: Hantek Страницы: 37

Бренд: SONIQ Страницы: 12

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды