background image

PAGE 52 — MT76D RAMMER • OPERATION AND PARTS MANUAL — REV. #7 (07/14/16) 

TERMS AND CONDITIONS OF SALE — PARTS

PAYMENT TERMS

Terms of payment for parts are net 30 days.

FREIGHT POLICY

All parts orders will be shipped collect or 

prepaid with the charges added to the invoice. 

All shipments are F.O.B. point of origin. 

Multiquip’s responsibility ceases when a 

signed manifest has been obtained from the 

carrier, and any claim for shortage or damage 

must be settled between the consignee and 

the carrier.

MINIMUM ORDER

The minimum charge for orders from Multiquip 

is $15.00 net. Customers will be asked for 

instructions regarding handling of orders not 

meeting this requirement.

RETURNED GOODS POLICY

Return shipments will be accepted and 

credit will be allowed, subject to the following 

provisions:

1.  A Returned Material Authorization 

must be approved by Multiquip prior to 

shipment. 

2.  To obtain a Return Material Authorization, 

a list must be provided to Multiquip 

Parts Sales that defi nes item numbers, 

quantities, and descriptions of the items 

to be returned.
a.  The parts numbers and descriptions 

must match the current parts price 

list.

b.  The list must be typed or computer 

generated.

c.  The list must state the reason(s) 

for the return.

d.  The list must reference the sales 

order(s) or invoice (s) under 

which the items were originally 

purchased.

e.  The list must include the name 

and phone number of the person 

requesting the RMA.

3.  A copy of the Return Material Authorization 

must accompany the return shipment.

4.  Freight is at the sender’s expense. All 

parts must be returned freight prepaid to 

Multiquip’s designated receiving point.

5.  Parts must be in new and resalable 

condition, in the original Multiquip 

package (if any), and with Multiquip part 

numbers clearly marked.

6.  The following items are not returnable:

a.  Obsolete parts. (If an item is in the 

price book and shows as being 

replaced by another item, it is 

obsolete.)

b.  Any parts with a limited shelf life 

(such as gaskets, seals, “O” rings, 

and other rubber parts) that were 

purchased more than six months 

prior to the return date.

c.  Any line item with an extended 

dealer net price of less than 

$5.00.

d.  Special order items.
e.  Electrical components.
f.  Paint, chemicals, and lubricants.
g.  Decals and paper products.
h.  Items purchased in kits.

7.  The sender will be notifi ed of any material 

received that is not acceptable.

8.  Such material will be held for five 

working days from notifi cation, pending 

instructions. If a reply is not received 

within five days, the material will be 

returned to the sender at his expense.

9.  Credit on returned parts will be issued 

at dealer net price at time of the original 

purchase, less a 15% restocking 

charge.

10.  In cases where an item is accepted, for 

which the original purchase document 

can not be determined, the price will be 

based on the list price that was effective 

twelve months prior to the RMA date.

11.  Credit issued will be applied to future 

purchases only.

PRICING AND REBATES

Prices are subject to change without prior 

notice. Price changes are effective on a 

specifi c date and all orders received on or 

after that date will be billed at the revised price. 

Rebates for price declines and added charges 

for price increases will not be made for stock 

on hand at the time of any price change.

Multiquip reserves the right to quote and 

sell direct to Government agencies, and to 

Original Equipment Manufacturer accounts 

who use our products as integral parts of their 

own products.

SPECIAL EXPEDITING SERVICE

A $35.00 surcharge will be added to the 

invoice for special handling including bus 

shipments, insured parcel post or in cases 

where Multiquip must personally deliver the 

parts to the carrier.

LIMITATIONS OF SELLER’S LIABILITY

Multiquip shall not be liable hereunder for 

damages in excess of the purchase price of 

the item with respect to which damages are 

claimed, and in no event shall Multiquip be 

liable for loss of profi t or good will or for any 

other special, consequential or incidental 

damages.

LIMITATION OF WARRANTIES

No warranties, express or implied, are 

made in connection with the sale of parts or 

trade accessories nor as to any engine not 

manufactured by Multiquip. Such warranties 

made in connection with the sale of new, 

complete units are made exclusively by a 

statement of warranty packaged with such 

units, and Multiquip neither assumes nor 

authorizes any person to assume for it 

any other obligation or liability whatever in 

connection with the sale of its products. Apart 

from such written statement of warranty, 

there are no warranties, express, implied or 

statutory, which extend beyond the description 

of the products on the face hereof.

Effective:  February 22, 2006

Содержание Mikasa MT76D























































Отзывы: