background image

05

06

As light becomes less, 

current decreases

As light becomes less, open circuit voltage drops

U( V )

I ( A)

20℃

50℃

70℃

60℃

40 ℃

30℃

I (A)

U( V)

As temperature falls, 

current does not change, 

power increases 

Relationship between the solar panel 

output characteristics and the light 

             

The  maximum  power  point  often  changes  due  to  different  ambient  temperature  and  lighting 

conditions.  Our  MPPT  controller  can  adjust  the  parameters  from  time  to  time  according  to  different 
conditions, so that the system is always near the maximum power point. The entire process is completely 
automatic and does not require any adjustments by the user.

PWM

 

charge

U ( V )

I ( A )

P( W )

VP Curve

VI Curve

94. 5

81. 0

67. 5

54. 0

27. 0

40. 5

13. 5

0. 0

19. 6

16. 8

14. 0

11. 2

8. 4

5. 6

2. 8

0. 0

0. 5

1. 0

1. 5

2. 0

2. 5

3. 0

3. 5

4. 0

4. 5

5. 0

MPPT Point

3. Technical Parameters

Values

Parameter name

12V/24V/36V/48V

0.5W

9V~64V

150V

(Battery 2)~120V

60A

40A

800W/12V; 1600W/24V; 2400W/36V; 3200W/48V

≤98%

99%

5V*n

6V*n

Day to night: 5min (default) Night to day: 1min

Isolated RS485 :baud rate 9600, data bit8, stop bit1, 

no check bit; default address 1

Natural heat dissi heat dissipation by fan

By RS485 communication cables, 

multiple controllers can work in parallel to control charging 

For battery temperature protection and 

lead-acid battery temperature compensation

Battery over-charge protection, battery over-discharge protection, 

battery reverse polarity protection, PV reverse polarity

 protection, nighttime reverse charge protection, internal 

over-temperature protection, charge over-current protection, 

load over-current protection, load short-circuit protection, 

fan fault protection, etc.

-

10℃

~+

65℃

≤ 3000m

IP32

3.6kg

275*167*90mm

As temperature rises, open circuit voltage drops

Solar p

anel temperatur

e

Relationship between the solar panel 

output characteristics and the temperature

System voltage

No-load loss

Battery voltage

Maximum PV open circuit voltage

Maximum power point voltage range

Rated charge current

Rated load current

Solar panel power

Charge conversion efficiency

MPPT tracking efficiency

Light control ON voltage

Light control OFF voltage

Light control delay

 

Communication mode

Cooling mode

Parallel charging

Battery outside temperature sampling

Protections

Operating temperature

Altitude

IP rating

Weight

Dimensions

Содержание 104714











Отзывы: