MPFiltri ICM Скачать руководство пользователя страница 3

Страница: 3 / 26

Introduction

1 Introduction

1.1 Overview

The ICM measures and quantiﬁes the numbers of solid contaminants in Hydraulic,

Lubrication and Transmission applications. The ICM is designed to be an accu-

rate instrument for permanently installed applications utilising mineral oil as the

operating ﬂuid.
The unit can operate using any of the international standard formats ISO 4406:1999,

NAS 1638, AS 4059E and ISO 11218.
The ICM incorporates a CAN-bus interface so that it can be connected to an existing

CAN-bus network. This allows the ICM to be easily integrated into industrial,

mobile, agricultural and military applications.

1.2 CAN-bus Standards

The ICM supports the major CAN-bus basic message format standards CAN 2.0A

(11 bit identiﬁers) and CAN2.0B (29 bit identiﬁers).
J1939 and CanOpen are higher level protocols built on these basic standards. J1939

uses CAN2.0A, and CanOpen uses CAN2.0B. The ICM does not implement either

of these protocols. Instead it deﬁnes a few CAN-bus messages to communicate

data. However the message identiﬁers have been chosen so as to allow operation

with both J1939 and CanOpen. Generally it should be possible to use the ICM with

either, as well as other CAN-bus systems.

1.3 Installation Outline

•

Perform a general installation and check of the ICM as detailed in the main

product user guide.

•

Perform a one-oﬀ general conﬁguration check of the ICM using a PC running

LPA-View

. This procedure is described in the main ICM user guide. You will

need a suitable RS485 interface, such as the ICM-USBi.

For example set it to test continuously and to automatically start testing on power-up

Содержание ICM



























Результаты поиска

Содержание ICM

Отзывы:

Похожие инструкции для ICM

Бренды по названию

Популярные бренды

MPFiltri ICM, Руководство пользователя

Результаты поиска

Содержание ICM

Отзывы:

Похожие инструкции для ICM

Бренды по названию

Популярные бренды