Moxa Technologies EtherDevice EDS-518A Series Скачать руководство пользователя | Manualshive

Страница: 69 / 97

background image

EDS-518A Series User’s Manual

Featured Functions

3-54

System Events

Warning e-mail is sent when…

Switch Cold Start

Power is cut off and then reconnected.

Switch Warm Start

EDS-518A is rebooted, such as when network
parameters are changed (IP address, subnet mask,
etc.).

Power Transition (On

Æ

Off)

EDS-518A is powered down.

Power Transition (Off

Æ

On)

EDS-518A is powered up.

DI1 (On

Æ

Off)

Digital Input 1 is triggered by on to off transition

DI1 (Off

Æ

On)

Digital Input 1 is triggered by off to on transition

DI2 (On

Æ

Off)

Digital Input 2 is triggered by on to off transition

DI2 (Off

Æ

On)

Digital Input 2 is triggered by off to on transition

Configuration Change Activated A configuration item has been changed.
Authentication Failure

An incorrect password is entered.

Comm. Redundancy Topology
Changed

Spanning Tree Protocol switches have changed their
position (applies only to the root of the tree).
The Master of the Turbo Ring has changed or the
backup path is activated.

Port Events

Warning e-mail is sent when…

Link-ON

The port is connected to another device.

Link-OFF

The port is disconnected (e.g., the cable is pulled out,
or the opposing device shuts down).

Traffic-Overload

The port’s traffic surpasses the Traffic-Threshold for
that port (provided this item is Enabled).

Traffic-Threshold (%)

Enter a non-zero number if the port’s
Traffic-Overload item is Enabled.

Traffic-Duration (sec.)

A Traffic-Overload warning is sent every

Traffic-Duration

seconds if the average

Traffic-Threshold is surpassed during that time
period.

NOTE

The

Traffic-Overload

,

Traffic-Threshold (%)

, and

Traffic-Duration (sec.)

Port Event items

are related. If you Enable the Traffic-Overload event, then be sure to enter a non-zero
Traffic-Threshold percentage, as well as a Traffic-Duration between 1 and 300 seconds.

NOTE

Warning e-mail messages will have the

sender

field formatted

in the form:

MOXA_EtherDevice_Switch_0001@Switch_Location

where

MOXA_EtherDevice_Switch

is the default Switch Name,

0001

is EDS-518A’s serial

number, and

Switch_Location

is the default Server Location.

Refer to the Basic

Settings

section to see how to modify Switch Name and Switch Location.

«
...
67
68
69
70
71
...
»

Содержание EtherDevice EDS-518A Series


































































































Отзывы:

Нет отзывов

Похожие инструкции для EtherDevice EDS-518A Series

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

AirPlus G DWL-G710

Бренд: D-Link Страницы: 5

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 5

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

Бренд: Lattice Semiconductor Страницы: 15

iCE40 UltraLite

Бренд: Lattice Semiconductor Страницы: 13

Бренд: Quantum Страницы: 20

Бренд: Raritan Страницы: 4

Бренд: Aleratec Страницы: 12

Бренд: Nakayo Страницы: 119

NOVA300 AML02304U1

Бренд: Nexxt Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды