Moxa Technologies AirWorks AWK-3131A Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 109

Moxa Technologies AirWorks AWK-3131A Скачать руководство пользователя страница 82

AirWorks AWK-3131A

Web Console Configuration

3-67

Troubleshooting

This feature allows you to quickly obtain the current system status and provide diagnostics information to
Moxa engineers.

To export the current device information, click Export.

Wi-Fi Mirror Port

A Wi-Fi mirror port can help you obtain the current Wi-Fi communication behavior of your network over the
current channel when it is not convenient to set up a Wi-Fi sniffer in the system operating environment.

To setup a Wi-Fi mirror port, you will need a computer with the Wireshark tool installed, which will be used
to connect to the AWK device via the Ethernet.

NOTE

A Wi-Fi mirror port is useful for gathering information. However, the DFS function may not work properly
when you enable the Wi-Fi Mirror Port function. Hence, we recommend disabling the Wi-Fi Mirror Port
function during normal usage.

To set up a Wi-Fi mirror port for short-term monitoring, do the following:

1.

Enter the duration in the Capture Wi-Fi Frames box.
You can enter a value between 1 to 180 seconds.

2.

Click Capture

3.

Wait for a timeout on the web console

You will be able to download a report from the web browser.

To set up a Wi-Fi mirror port for long-term monitoring, do the following:

1.

On the Wi-Fi Mirror Port page, set the Remote Capture option to Enable.

2.

Run the Wireshark tool on your computer, click Capture and then click Options.

3.

In the Input tab of the Wireshark tool, click Manage Interfaces

«
...
80
81
82
83
84
...
»

Содержание AirWorks AWK-3131A














































































































Отзывы:

Нет отзывов