Moxa Technologies AirWorks AWK-3131A Скачать руководство пользователя страница 53

Страница: 53 / 109

AirWorks AWK-3131A

Web Console Configuration

3-38

You can check the IP assignment status under Status



DHCP Client List.

DHCP server

Setting

Description

Factory Default

Enable

Enables AWK-3131A as a DHCP server

Disable

Disable DHCP server function

Default gateway

Setting

Description

Factory Default

IP address of a default
gateway

The IP address of the router that connects to an outside
network

None

Subnet mask

Setting

Description

Factory Default

subnet mask

Identifies the type of sub-network (e.g., 255.255.0.0 for a
Class B network, or 255.255.255.0 for a Class C network)

None

Primary/ Secondary DNS server

Setting

Description

Factory Default

IP address of Primary/
Secondary DNS server

The IP address of the DNS Server used by your network.
After entering the DNS Server’s IP address, you can use URL
as well. The Secondary DNS server will be used if the Primary
DNS server fails to connect.

None

Start IP address

Setting

Description

Factory Default

IP address

Indicates the IP address which AWK-3131A can start
assigning

None

Содержание AirWorks AWK-3131A













































































































Результаты поиска

Содержание AirWorks AWK-3131A

Отзывы:

Moxa Technologies AirWorks AWK-3131A, Руководство пользователя, Страница: 53 / 109

Результаты поиска

Содержание AirWorks AWK-3131A

Отзывы: