background image

- 13 - 

Spread Spectrum 
and Modulation 
(typical)

 

 

DSSS with DBPSK, DQPSK, CCK 

 

OFDM with BPSK, QPSK, 16QAM, 64QAM 

 

802.11b: 
CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps, 
DBPSK @ 11 Mbps 

 

802.11a/g:   
64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, 
QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps 

 

802.11n:   
64QAM@300 Mbps to BPSK @ 6.5 Mbps 
(multiple rates supported) 

Operating Channels   
(central frequency)

 

US:   
• 2.412 to 2.462 GHz (11 channels)   
• 5.180 to 5.240 (4 channels)   
• 5.260 to 5.320 (4 channels)*   
• 5.500 to 5.700 GHz (8 channels, excluding 5.600 
to 5.640 GHz)*   
• 5.745 to 5.825 GHz (5 channels) 
EU: 
• 2.412 to 2.472 GHz (13 channels)   
• 5.180 to 5.240 GHz (4 channels)   
• 5.260 to 5.320 GHz (4 channels)*   
• 5.500 to 5.700 GHz (11 channels)*     
JP:   
• 2.412 to 2.484 GHz (14 channels)   
• 5.180 to 5.240 GHz (4 channels)   
• 5.260 to 5.320 GHz (4 channels)*   
• 5.500 to 5.700 GHz (11 channels)* 

*DFS (Dynamic Frequency Selection) channel support: In AP mode, when 
a radar signal is detected, the device will automatically switch to another 
channel. However according to regulations, after switching channels, a 
60-second availability check period is required before starting the service 

Security

 

 

SSID broadcast enable/disable 

 

Firewall for MAC/IP/Protocol/Port-based filtering 

 

64-bit and 128-bit WEP encryption, WPA / 
WPA2-Personal and Enterprise (IEEE 
802.1X/RADIUS, TKIP and AES) 

Transmission Rates

 

802.11b: 1, 2, 5.5, 11 Mbps 
802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps 
802.11n: 6.5 to 300 Mbps (multiple rates supported) 

TX Transmit Power  802.11b:   

• Typ. 26±1.5 dBm @ 1 Mbps   
• Typ. 26±1.5 dBm @ 2 Mbps   
• Typ. 26±1.5 dBm @ 5.5 Mbps   
• Typ. 25±1.5 dBm @ 11 Mbps   
802.11g:   
• Typ. 23±1.5 dBm @ 6 to 24 Mbps   
• Typ. 21±1.5 dBm @ 36 Mbps   
• Typ. 19±1.5 dBm @ 48 Mbps   
• Typ. 18±1.5 dBm @ 54 Mbps   
802.11n (2.4 GHz):   
• Typ. 23±1.5dBm @ MCS0 20 MHz   
• Typ. 21±1.5dBm @ MCS1 20 MHz   
• Typ. 21±1.5dBm @ MCS2 20 MHz   
• Typ. 21±1.5dBm @ MCS3 20 MHz   

Содержание Airworks AWK-3131A-M12-RCC



















Отзывы: