background image

9

Model EA91A&EA90A

※If the device is in conditions of ① or ②, contact our sales branch or sales agent.

※Refer to Item 9.2 "Dimension of Mounting Hardware" for 
 dimension of each part.

※The ambient temperature in the non-explosion-
   protected environment is ‒40 to 100℃

−20〜60℃

−20〜60℃

80〜110 kPa, Absolute Press.

Environmental

Conditions

Model 

Ambient Temp.

Atmospheric 

Pressure

(5)  Orifice Plate Check 
 Remove pilot cover, and check orifice plate appropriate 

for actuator capacity is installed and set.

Connector Arm

Stem Clamp

For Model 2900

For Model 3300

For Model 3800

For Model 2800

Bracket

Feedback Lever

4.2 Installation Conditions

4.2.1 Locations for Installation

The models EA91A and EA90A electro-pneumatic 
positioner can be installed and used at the hazardous 
area in accordance with gases to be used. 

4.3 Pre-Installation Check

(1)  Nameplate  Check  (related  to  specifications  and 

explosion-protected type) 

   Check the content of the nameplate attached to the main 

body of the positioner whether the ordered specification 
is conformed with. 

(2)  Appearance Check 
   Check the presence of damage on the device due to 

transport. 

(3)  Accessory Identification
   Lever Type : Bracket, Stem Clamp (Connector Arm       
         included), Feedback Lever, and Connectr 

        Pin

  Buit-in Cam Type : Bracket, Connecting Shaft, Set 

        Screw, Spacer Bolt, and Set Spring 

  Also, the relative bolts, nuts, vises, and washers, etc. are 

 attached. 

(4)  Pressure Gauge Check

①If the equipment may cause to be exposed to the radiation from plant facilities and the 

ambient temperature may be abnormally high, take appropriate measures to insulate the 
heat. 

② If installing the equipment under the special conditions (vibration, corrosive atmosphere, 

always be exposed to drain), take appropriate measures to protect from such conditons.

4.2.2 Environmental Conditions

The applicable environmental conditions are shown in 
the right table.

CAUTION

IMPORTANT

IMPORTANT

Model EA91A

Flameproof Type

Model EA90A

Intrinsic Safety Type 

Be sure not to provide overpressure because 

the  pressure  gauge  appropriate  for  supply 

air pressure is installed. 

Although  orifice  plate  that  conforms  to  the 

order  specifications  is  installed  at  factory 

shipment, check it again. (Refer to Item 4.6.1)

Содержание EA90A
































Отзывы: