background image

This guide is provided as a help and not a total solution for every installation. 

Common sense and concern for customers equipment will make for a good installation. 

 

 

3

 

 
 

 
MotoSAT DataStorm Mobile Two-Way Internet  
User’s Manual Addendum 
Regulatory Information

 

 

This device complies with Part 15 of the FCC Rules.  Operation is 
subject to the following two conditions: (1) this device may not cause 
harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 
 

The Lower Control Unit (LCU-1) and Upper Control Unit (UCU-1) 
components of the DataStorm (together “the equipment”), and the 
associated connections, have been tested and found to comply with the 
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful 
interference in a residential installation.  This equipment generates uses 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio 
communications.  However, there is no guarantee that interference will not 
occur in a particular installation.  If this equipment does cause harmful 
interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver.

 

 

Connect the equipment into an outlet on a circuit different from 
that to which the receiver is connected.

 

 

Consult the dealer or an experienced radio/TV technician for 
help.

 

 

Changes or modifications not approved by MotoSAT [Mobile 
Technology, Inc.] for compliance could void the user’s authority to 
operate the equipment. 

 
 
 
 
 
 
 
 
 

 

 

Содержание DataStorm




























Отзывы: