background image

Motortronics VCM Series

Thank you for purchasing this Motortronics VCM Series sensorless vector 
AC drive. When properly installed, operated and maintained, the VCM 
will provide a lifetime of reliable operation. It is mandatory that the 
person who operates, inspects and maintains this equipment thoroughly 
reads and understands this manual. This will insure safe and reliable 
operation of the controller.

This unit has been put through demanding tests at the factory prior to 
shipment. Before unpacking, check the following:

•  Verify that the model number on the box matches your purchase 

order

•  Inspect for possible damage (if damaged, notify the freight carrier 

and fi le a cliam within 15 days of receipt)

After unpacking, please check the following:

•  Verify the label specifi cations match your application requirement.
•  Check all electrical connections and screws. Verify that there is no 

visible damage to any of the components.

 

WARNING!

 

Do not service equipment with voltage applied!

  Unit can be a source of fatal electrical shock! To avoid shock haz-

ard, disconnect main power and wait until the LED on the main 
control board goes out before working on the control Warning 
labels (not supplied) must be attached to terminals, enclosure 
and control panel.

  Unit does not provide overspeed protection or incorporate cur-

rent limiting control.

  To obtain optimum operation from your VCM Series sensorless 

vector AC drive, it is strongly recommended that this manual is 
read and understood.

CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: [email protected]

Содержание VCM series














Отзывы: