Motorola WR850 Скачать руководство пользователя

Страница: 24 / 123

Section 2

Installation

2-10 WR850

Your PC’s wireless adapter may need to be configured to work with the WR850.

By default, the WR850 has a LAN IP Address of 192.168.10.1, and dynamically assigns

an IP Address to connected devices. The PC will not communicate properly with the

WR850 if the wireless adapter is not configured either:

(a) to accept a dynamic IP Address, or
(b) with a compatible static IP Address (i.e., 192.168.10.x, where x is a number

between 2 and 254).

To make any necessary adjustments to your PC’s wireless adapter, you can follow the

instructions in this section under

Configuring Computers to Communicate with the

WR850

To connect the PC to the WR850 through a wireless connection, use your PC’s wireless

adapter utility to verify:

(a) the selection of the SSID (Service Set Identifier) of the WR850, which by default

is set to

motorolaABCDEF012345

, where the final 12 characters represent the

WR850’s Wireless MAC address (see the image below to identify the WR850

Wireless MAC address from the product label),

(b) that authentication is set to Open, since the WR850 by default has no wireless

authentication enabled, and

encryption enabled.

FOR HOME OR OFFICE USE

Tested To Comply

With FCC Standards

MODEL: WR850G

INPUT VOLTAGE: +5VDC, 2A

FCC ID: F2NWR850G

MODEL WR850G

PART NUMBER: AAAAAA-BBB-CC

S/N: PPPPMMYJJJSSSSSCAABBCCCC

WIRELESS MAC: AB CD EF 01 23 45

WAN MAC: AB CD EF 01 23 45

MADE IN TAIWAN

INPUT VOLTAGE: +5VDC, 2A

FCC ID: F2NWR850G

FOR HOME OR OFFICE USE

Tested To Comply

With FCC Standards

MODEL: WR850G

WIRELESS MAC: AB CD EF 01 23 45

WAN MAC: AB CD EF 01 23 45

MADE IN TAIWAN

MODEL WR850G

PART NUMBER: AAAAAA-BBB-CC

S/N: PPPPMMYJJJSSSSSCAABBCCCC

Wireless MAC address

Refer to your wireless adapter’s documentation for instructions on how to review and

adjust these settings.

NOTE: You can make wireless connections between the WR850 and other devices by

repeating Steps 3 and 4 with each of those devices, but it is recommended to wait
until after securing your wireless network to do so.

Содержание WR850




























































































































Результаты поиска

Содержание WR850

Отзывы:

Похожие инструкции для WR850

Бренды по названию

Популярные бренды

Motorola WR850, Руководство пользователя

Результаты поиска

Содержание WR850

Отзывы:

Похожие инструкции для WR850

Бренды по названию

Популярные бренды