Using additional handsets
23
14. Using additional handsets
You can use up to five D1110 additional handsets with your
D1110 base to extend your phone system without needing to
install extension sockets for each new phone.
Your D1110 handset can also be registered to up to 3 other
bases. You can then select the base you would prefer to use.
If you have purchased a D1110 multiple pack any additional
handsets come pre-registered to the base.
If you have purchased an additional handset separately you
must register it to your D1110 base before it can be used.
Registering an additional handset
At the base:
1.
Press and hold
p
for 2 seconds until the base Power
starts flashing. The base will remain in registration mode for
90 seconds.
At the handset:
1.
If the handset is new and the display shows
Please Register
.
Press
Menu
. Scroll
u
to
Registration
. Press
Select
.
Or
If the handset has already been registered to another base
the standby display is shown. Press
Menu
, scroll
u
or
d
to
Registration
and press
Select
.
2.
Register Handset
is highlighted. Press
Select
.
3.
Bases are displayed. If necessary, scroll
u
or
d
to a new
base you wish to register your D1110 handset to and press
Select
.
4.
Enter the system PIN and press
OK
. (Default setting =
0000)
5.
The display shows
Searching Base X
(where X is the chosen
base number) then
Handset Registered
.
The handset is automatically assigned the next available
handset number.
If registration is not successful first time, please repeat the
process again in case the base registration period ran out of
time.
If there are already 5 handsets registered to the base, the
registration will fail. You must de-register another handset before
you can register the new one.
Select a base
If your D1110 handset is registered to more than one base, you
can select which base to use.
1.
Press
Menu
, scroll
u
or
d
to
Registration
and press
Select
.
2.
Scroll
d
to
Select Base
and press
Select
.
3.
All base numbers are displayed.
(In use)
is added to bases
where the handset was previously registered to. Scroll
u
or
d
to the base you want and press
Select
.
4.
Display shows
Searching Base…
. then the standby display for
that base.
De-register a handset
Use one handset to de-register another. You cannot de-register
the handset you are using.
1.
Press
Menu
, scroll
u
or
d
to
Registration
and press
Select
.
2.
Scroll
d
to
De-register
and press
Select
.
3.
Enter the system PIN and press
OK
. (Default setting =
0000)
4.
Scroll
u
or
d
to the handset you want to de-register and
press
Select
.
5.
Press
Yes
to confirm or
No
to cancel.
6.
Press
Back
to return to the previous menu level or
>
to
return to standby.
15. Help
Phone does not work
• Have you installed the batteries correctly?
• Check that the mains power is correctly connected.
No dial tone
• Is the telephone cord of the base plugged into the phone
socket?
• Check that the mains power is correctly connected to the
base and to the handset charger(s).
• Only use the telephone cord supplied with the phone.
Cannot dial out or receive calls
• Check that the mains power is correctly connected.
• The batteries may need recharging.
• Has there been a power cut? If so, place the handset back on
the base for 10 seconds and try again. If it still does not work
disconnect the batteries and mains power for 10 minutes, then
reconnect and try again.
You have a dial tone, but the phone will not dial out
• You may need to change the dial mode from tone to pulse,
see page 12.
• If you are connected to a switchboard, check whether you
need to dial an access code.
Handset does not ring
• The ringer volume may be switched off, see page 11.
• Check that the mains power is correctly connected.
• Check that the line cord is connected.
• Make sure the handset is registered to the base, see
page 23.
No display
• The batteries may be flat, dead or incorrectly inserted.
Recharge or replace the batteries.
icon flashes
• Is the handset registered correctly to the base, see page 23.
• Check that the mains power is correctly connected.
• Check that the handset is within range of the base.
• The batteries are low, place the handset on the base/
charger to recharge.
• Switch OFF the Eco mode.
icon not scrolling
• Try cleaning the charging contacts.
• Check that the mains power is correctly connected.
