manualshive.com logo in svg

Motorola Canopy Backhaul Module, Руководство пользователя

Поделиться
Скачать
Motorola Canopy Backhaul Module Скачать руководство пользователя страница 9

Backhaul User Manual   Issue 3

Page 9 of 53

PRODUCT DESCRIPTION

Canopy Backhaul

Backhaul links provide point-to-point connectivity either as a standalone link or feeding an Access
Point cluster as part of a Canopy network.

Backhaul modules are available in both the 5.2 and 5.7 bands and in both 10 and 20 Mbps. 5.7
backhauls can be used with reflectors on either or both ends. 5.2 backhauls cannot be used with
reflectors in the US or Canada due to regulatory agency restrictions.

The following table shows typical ranges for each type of backhaul.

Module Type

Modulation Rate

Reflectors

Typical Range

5200 BH10 (DES)
5201 BH10 (AES)

10

None allowed in US or
Canada

2 miles (3.6 km)

5700 BH10 (DES)
5701 BH10 (AES)

10

None

2 miles (3.6 km)

5700 BH10 (DES)
5701 BH10 (AES)

10

One end

10 miles (16 km)

5700 BH10 (DES)
5701 BH10 (AES)

10

Both ends

35 miles (56 km)

5700 BH20

20

None

1 mile (1.6 km)

5700 BH20

20

One end

5 miles (8 km)

5700 BH20

20

Both ends

35 miles (56 km)

When using Backhauls in standalone links, the type of Backhaul is selected based on data needs
and range needs. When using Backhauls in a network and co-locating a BH with Access Points,
the type of backhaul is usually selected based on having the BH in a different band than the APs.
In other words, if the APs are 5700s, the BH is a 5200 and vice versa. While distance separation of
100 vertical feet (30 m) on a tower can allow use of co-located APs and BHs in the same band,
choosing cross-band APs and BHs is usually the better choice.

Module Description

The base cover of your Canopy Backhaul is easily removed by depressing the release lever on the
back of the cover.

Ethernet

 

Cable

 

Base  Cover

 

Release

 

Lever

 

Base  Cover

 

FIGURE 1

Содержание Canopy Backhaul Module






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды