Motorola Canopy Backhaul Module Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 53

background image

Backhaul User Manual Issue 3

Page 21 of 53

is not enabled, AES modules can communicate with DES modules.

Branding

On each Canopy module, the web-based interface screens have a Canopy logo that can be
replaced with an operator’s company logo. The Canopy logo file is called

canopy.jpg

and the

replacement file must also be called

canopy.jpg

. The new file is transferred via FTP to the module

and then added to a special filesystem through a telnet session. The following command can be
used during a telnet session:

•

addwebfile – add a custom logo file to the filesystem

•

clearwebfile – clear the customer logo file from the filesystem

•

lsweb – list the custom logo file and display the storage space available on the filesystem

The following is a sample FTP session:

> ftp 169.254.1.1

Connected to 169.254.1.1
220 FTP server ready
Name (169.254.1.1:none):

root

331 Guest login ok
Password:

<

password-if-configured

>

230 Guest login ok, access restrictions apply.

ftp

> binary

200 Type set to I
ftp

> put canopy.jpg

ftp

> quit

221 Goodbye

The following is a sample telnet session:

/---------\
C A N O P Y

Motorola Broadband Wireless Technology Center
(Copyright 2001, 2002 Motorola Inc.)

Login:

root

Password:

<

password-if-configured

>

> lsweb

Flash Web files
free directory entries: 32
free file space 64336 bytes

>

addwebfile canopy.jpg

>

lsweb

Flash Web files
/canopy.jpg 7867
free directory entries: 31
free file space: 56468

>

clearwebfile

> lsweb

Flash Web files
free directory entries: 32
free file space 64336 bytes

SNMP

Simple Network Management Protocol (SNMP) can be utilized to monitor the Canopy modules.
The standard MIB-II (systems and interfaces) objects are programmed into the modules. For

«
...
19
20
21
22
23
...
»

Содержание Canopy Backhaul Module






















































Отзывы:

Нет отзывов

Похожие инструкции для Canopy Backhaul Module

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Taie Страницы: 28

ESD-5550 Series

Бренд: GAC Страницы: 12

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: IBM Страницы: 38

Бренд: Lawler Страницы: 5

Бренд: Oceanic Systems Страницы: 8

Бренд: Parker Страницы: 38

Бренд: Parker Страницы: 2

Бренд: DigiPower Страницы: 27

Бренд: JASTEC Страницы: 18

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

Бренд: Quickie Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды