manualshive.com logo in svg

Motorola Canopy Backhaul Module, Руководство пользователя

Поделиться
Скачать
Motorola Canopy Backhaul Module Скачать руководство пользователя страница 40

EthBusErr:  

displays the total number of Ethernet bus errors on the Ethernet controller.

CRCError:  

displays the total number of CRC errors on the Ethernet controller.

RxOverrun:  

displays the total number of receiver-overrun errors on the Ethernet controller.

Late Collision:  

displays the total number of late collisions on the Ethernet controller.   A normal

collision occurs during the first 512 bits of the frame transmission.  If a collision occurs after the 512
bit times, then it is considered a late collision.  A late collision should be taken as a serious network
problem, since it causes the frame being transmitted to be discarded.  The most common cause of
late collisions is a mismatch between duplex configurations at each end of a link segment.

RetransLimitExp:  

displays the total number of retransmit limit expirations.

TxUnderrun:  

displays the total number of transmission-underrun errors on the Ethernet controller.

CarSenseLost:  

displays the total number of carrier sense lost errors occurred on the Ethernet

controller.

Expanded Stats

Clicking on the 

Expanded Stats

 link will display a number of pages of statistics that are maintained

by the Canopy module.  Canopy Technical Support may ask the operator for specific information in
this section when troubleshooting an issue.

Содержание Canopy Backhaul Module






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды