manualshive.com logo in svg

Motorola C330, Руководство по обслуживанию

Поделиться
Скачать
Motorola C330 Скачать руководство пользователя страница 30

26

 

        August 20, 2002 

6881040B65

Disassembly

Product Family 0C35

Battery Removal and Replacement

Battery date codes are explained in the Battery Date Code section on page 14

Before handling the battery, please observe the battery cautions listed below.

1.

Remove the rear housing, SIM, endo assembly, and front endo housing as 
described in the procedures.

2.

Disconnect the battery connector from the connector socket as shown in 
Figure 9. 

3.

Hold the battery by its case and remove it from the transceiver board. Do not 
pull on the battery wires as they may become disconnected from the battery 
pack or the battery connector. 

   

4.

To replace, align the battery connector cable with the battery connector socket. 
The connector and socket are designed to maintain the correct polarity. 

5.

Replace the front endo housing, endo assembly, SIM, and rear housing as 
described in the procedures.

G

Do not handle batteries with wet or sweaty hands.
Do not short the positive or negative terminals
Non conductive tweezers or grasping tools are to be used for battery connector 
manipulation, assembly, and disassembly. 

020193o

Figure 9. Removing and Replacing the Battery

E

There is a danger of explosion if the Lithium ion battery is replaced incorrectly. 
Replace only with the same type of battery or equivalent as recommended by the 
battery manufacturer. Dispose of used batteries according to the manufacturer’s 
instructions.

TRANSCEIVER BOARD

BATTERY

BATTERY CONNECTOR

BATTERY SWITCH

DISASSEMBLY 

TOOL

Содержание C330


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды