manualshive.com logo in svg

Motorola ASTRO Digital Spectra, Подробное руководство по обслуживанию

Моторола ASTRO Digital Spectra - мощная рация с цифровым шифрованием для надежной коммуникации. Установочное руководство и руководство пользователя можно бесплатно скачать с {веб-сайт} для настройки и использования этого устройства. Надежный помощник в вашей работе или в повседневной жизни.

Поделиться
Скачать
background image

6881076C25-E

September 5, 2008

Troubleshooting Procedures

: Power Amplifier Procedures

4-29

The directional coupler samples a small amount of forward power during transmit. This power is 
rectified by a detector diode CR3904. This rectified DC voltage is fed back to the RPCIC where it is 
compared to a reference voltage. An error voltage is generated which is ultimately translated into the 
control voltage via RPCIC circuitry and amplifiers Q503 and Q504 on the command board. Control 
voltage is routed to the LLA stage, thereby completing the feedback loop. In operation, the control 
loop tends to maintain the forward detected voltage constant versus frequency and line voltage 
variations. Proper operation can be observed by monitoring the forward detected voltage while 
varying the supply voltage from 13.4 to 16.1 V. Forward detected voltage should not change more 
than a few hundreths of a volt. Note that the forward power may not necessarily be level if one of the 
other protection circuits such as temp-sense or current limit is engaged.

NOTE:

If any part of the power leveling circuitry is replaced, perform the power set procedure. See 
the 

ASTRO Digital Spectra and Digital Spectra Plus Mobile Radios Basic Service Manual

 

(6881076C20) for details.

Miscellaneous Circuits and Notes

Diode CR3840

 

acts as a reverse protect diode. This diode also protects from over-voltage 

conditions, as it has a Zener breakdown voltage of approximately 28 V. When replacing this diode, 
care must be taken to place the diode with the cathode marking ring down (towards the PC board)

NOTE:

The control voltage drive and K9.4 supplies from the command board are not current limited. 
A momentary short on either of these supplies will cause damage to transistors on the 
command board. Use caution when troubleshooting circuits that use these.

4.5.1.2  25/10 Watt Power Amplifier

This information will help you troubleshoot the Spectra radio. Use this information, along with the 
Theory of Operation, to diagnose and isolate the cause of failures. The principle tools needed to 
troubleshoot a circuit to the component level are the schematic and the Theory of Operation.

In addition to the schematic and theory, this section includes troubleshooting information that will 
help you test and check the circuits to localize and isolate problems.

Prior to troubleshooting, it is important to review the Theory of Operation, including specific 
precautions and troubleshooting methods. Because much of the radio's circuitry operates at high 
frequency, measurements must be taken very carefully. Notes and cautions are added to the text to 
alert the reader to this need in areas of greatest sensitivity

However, the need for extreme care does exist in all measurements and tests at high frequency.

4.5.1.2.1  General Troubleshooting and Repair Notes

Most of the common transmitter symptoms are caused by either failure of the power amplifier or a 
failure in the control circuitry. The initial troubleshooting effort should be toward isolating the problem 
to one of those two areas. If either the control voltage or keyed 9.4 V are zero, then the problem is 
likely to be in the control circuit. If those voltages are present, then the problem is more likely in the 
power amplifier circuit.

If, for diagnostic reasons, a chip component needs to be removed to facilitate testing, such as a 
series capacitor removed to allow for signal insertion, then the component(s) returned to the circuit 
should be new parts. The application of a soldering iron to many chip components will tend to cause 
leaching which could lead to failure.

After a PA board is replaced, or if any power control circuitry components are replaced, readjust the 
power according to instructions in the 

ASTRO Digital Spectra and Digital Spectra Plus Mobile Radios 

Basic Service Manual

 (6881076C20).

Содержание ASTRO Digital Spectra



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASTRO Digital Spectra

Yaesu VX-3R Manual preview
VX-3R
Бренд: Yaesu Страницы: 2
Yaesu FTM-400XDR Field Manual preview
FTM-400XDR
Бренд: Yaesu Страницы: 2
Yaesu FT-60R Quick Reference Manual preview
FT-60R
Бренд: Yaesu Страницы: 2
Yaesu FT-450 Technical Supplement preview
FT-450
Бренд: Yaesu Страницы: 69
TR TR3X User Manual preview
TR3X
Бренд: TR Страницы: 16
uAvionix Ping200SR User And Installation Manual preview
Ping200SR
Бренд: uAvionix Страницы: 31
König Electronic 5412810211012 Manual preview
5412810211012
Бренд: König Electronic Страницы: 116
Uniden UBC3000XLT Operating Manual preview
UBC3000XLT
Бренд: Uniden Страницы: 50
Metrici Observer Radar User Manual preview
Observer Radar
Бренд: Metrici Страницы: 9
PURE EVOKE-2S Owner'S Manual preview
EVOKE-2S
Бренд: PURE Страницы: 88
LENCO ODR-150 User Manual preview
ODR-150
Бренд: LENCO Страницы: 77
Telefunken TF-1594U Instruction Manual preview
TF-1594U
Бренд: Telefunken Страницы: 16
GEM GX700 Instruction Manual preview
GX700
Бренд: GEM Страницы: 18
Kenwood KRK-13 Application Note preview
KRK-13
Бренд: Kenwood Страницы: 9
Kenwood FM Transceiver TK-481 Specifications preview
FM Transceiver TK-481
Бренд: Kenwood Страницы: 2
Kenwood TK-2200 Instruction Manual preview
TK-2200
Бренд: Kenwood Страницы: 42
Kenwood FM Transceiver TK-481 Service Manual preview
FM Transceiver TK-481
Бренд: Kenwood Страницы: 55
Kenwood TK-2200 Brochure preview
TK-2200
Бренд: Kenwood Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды