manualshive.com logo in svg

Motorola AP-6511, Справочное руководство

Поделиться
Скачать
Motorola AP-6511 Скачать руководство пользователя страница 169

Wireless Configuration

 

6-35

2. Refer to the following read-only information on each listed QoS policy to determine whether an existing 

policy can be used as is, an existing policy requires edit or a new policy requires creation:

WLAN QoS Policy

Displays the name assigned to this WLAN QoS policy when it was initially 
created. The assigned policy name cannot be modified as part of the edit 
process. 

Wireless Client 
Classification

Lists each policy’s 

Wireless Client

 Classification as defined for this 

WLAN's intended traffic. The Classification Categories are the different 
WLAN-WMM options available to a radio. The 

Wireless Client

 

Classification types are:

WMM

 – Implies WiFi Multimedia QoS extensions are enabled on this 

radio. This allows different traffic streams between the wireless client and 
the access point to be prioritized according to the type of traffic (voice, 
video etc). The WMM classification is required to support the high 
throughput data rates required of 802.11n device support. 

Voice 

– Optimized for voice traffic. Implies all traffic on this WLAN is 

prioritized as voice traffic on the radio.

Video

 – Optimized for video traffic. Implies all traffic on this WLAN is 

prioritized as video traffic on the radio.

Normal

 – Optimized for best effort traffic. Implies all traffic on this WLAN 

is prioritized as best effort traffic on the radio.

Low

 – Optimized for background traffic. Implies all traffic on this WLAN is 

low priority on the radio.

SVP Prioritization

A green checkmark defines the policy as having 

Spectralink Voice 

Prioritization

 (SVP) enabled to allow the wireless controller to identify and 

prioritize traffic from Spectralink/Polycomm phones using the SVP 
protocol. Phones using regular WMM and SIP are not impacted by SVP 
prioritization. A red “X” defines the QoS policy as not supporting SVP 
prioritization.

WMM Power Save

Enables support for the WMM based power-save mechanism, also known 
as 

Unscheduled Automatic Power Save Delivery

 (U-APSD). This is primarily 

used by voice devices that are WMM capable. The default setting is 
enabled. 

Multicast Mask 
Primary

Displays the primary multicast mask defined for each listed QoS policy. 
Normally all multicast and broadcast packets are buffered until the 
periodic DTIM interval (indicated in the 802.11 beacon frame), when 
clients in power save mode wake to check for frames. However, for certain 
applications and traffic types, the administrator may want the frames 
transmitted immediately, without waiting for the DTIM interval. By 
configuring a primary and secondary multicast mask, an administrator can 
indicate which frames are transmitted immediately. Setting masks is 
optional and only needed if there are traffic types requiring special 
handling.

Multicast Mask 
Secondary

Displays the secondary multicast mask defined for each listed QoS policy. 

Содержание AP-6511



















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды