MotorGuide Digital Steering Скачать руководство пользователя страница 4

90-MM6900  

2

 

 

 

GENERAL INFORMATION 

 

Please read and retain this manual. The information within 
describes the proper procedures for safely installing, 
operating and maintaining your motor.  
The description and specifications contained herein were 
in effect at the time this manual was approved for printing. 
MotorGuide, whose policy is one of continual 
improvement, reserves the right to discontinue models at 
any time, to change specifications, designs, and methods 
of procedure without notice and without incurring 
obligation.  

Safety and operating information that is practiced along 
with good common sense can help prevent personal injury 
and product damage. 

 

 
 

DIGITAL MOTORS: 
If the motor automatically throttles back, it 
indicates something may be wrong with the motor 
and it should be taken in for service.

 

 

 
 

DIGITAL MOTORS: 
A slight voltage drain occurs when the trolling 
motor is continually connected to the battery for 
extended periods of time.  To prevent battery drain 
when not in use fro an extended period, 
disconnect the trolling motor from the power 
source. 

 

 
 

Disconnect the trolling motor from the battery(s) 
before charging. 

 
 
Safety DO’s and DON’Ts 
 

Do not allow children to operate the trolling motor 
without adult supervision. 
 
Do not modify the unit in any way or add accessories 
other than approved MotorGuide accessories. 

 
Do not power-wash your trolling motor.

 

 
Do disconnect the power from the motor when 
replacing the prop, removing debris around the prop, 
charging batteries, putting your boat on a trailer or 
when the motor is not in use. 
 
Do make sure the foot pedal is secured and the motor 
is securely locked into the stowed position when using 
a gasoline motor to move to another location, or when 
putting your boat on a trailer. 

 

Do secure loose items on your boat before traveling 
at high speeds across the water. 
 
 

How to Use This Manual

 

 
Review the following information carefully.  These 
notices will alert you to potential dangers and 
important information.   
 
The observance of 

WARNINGS and CAUTIONS

 

alone does not eliminate the possibility of personal 
injury or product damage.  Your close attention to the 
performance of recommended service procedures 
and the practice of responsible personal safety are 
major accident prevention measures. 
 
 
 
Failure to follow a safety WARNING can result in 
bodily injury. 
 
 

 

Failure to observe CAUTION instructions can result in 
failure or damage to the product or equipment. 
 
 
 
Signifies important information about your trolling 
motor. 
 
 
 
Signifies a statement calling attention to general 
information about your trolling motor. 
 
 

Specifications 
 

Model Volts Kwatts  Kilos 

T25 12 0.20 6.11 
T30 12 0.20 6.11 

30 12 0.20 7.08 
36 12 0.25 7.7 
40 12 0.25 7.7 
46 12 0.28 8.17 
54 12 0.34 10.7 
71 24 0.48 

15.92 

54 V 

12 

0.34 

10.7 

70 V 

24 

0.48 

15.92 

71 V 

24 

0.48 

19.92 

82 V 

24 

0.78 

22.4 

109 V 

36 

0.88 

24.2 

54 V DS 

12 

0.34 

10.7 

82 V DS 

24 

0.78 

21.8 

109 V DS

36 

0.88 

23.3 

!

!

!

!

WARNING 

!

WARNING 

!

WARNING 

!

CAUTION 

INFORMATION 

NOTE

     CAUTION 

!

!

Содержание Digital Steering























Отзывы: