Motion Access CONDOR SWING MA50777 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 12

Motion Access CONDOR SWING MA50777 Скачать руководство пользователя страница 5

MOTION

ACCESS

, LLC

automatic entrance solutions

5

For technical assistance call 866-357-8832

MA50777-MNL_revP1

10.

Install control box into header ensuring wires are not pinched, rotate retaining wings
into the header groove and tighten screws.

!

DANGER:

Never modify harnesses. Unsafe operation may result. For
technical assistance call MotionAccess 847-357-8832.

!

DANGER:

Stay clear of doors and keep fingers and hands way from
moving parts. The door may activate unexpectedly when
power is restored.

!

DANGER:

Route harnesses away from moving parts & sharp edges.

11.

Ensure you and others are clear of door(s) and mechanism.

12.

Connect power harness to controller and restore main power.

13.

Provide a continuous activation signal to the control; or set the jamb/function switch to
“Hold Open” if available. The spindle will rotate to the full open position.

14.

Attach arm to spindle and door (see instructions provided with arm). Stay clear of the
arms closing path as the loss of the activation signal or power will cause the arm to
swing quickly towards the closed position.

retaining
wing

«
...
3
4
5
6
7
...
»

Содержание CONDOR SWING MA50777













Отзывы:

Нет отзывов