background image

4

Installation requirements vary in different districts, and the local building officials have the final
authorization to approve your installation.  You should discuss the installation with them before
beginning. Please ask your dealer for further information.

 Do not connect to any air distribution duct or system

.

 Important: If the installation instructions are not followed carefully, it may cause
 dangerous situations like chimney - and house fires. Follow the instructions
 carefully and do not deviate from them as it may cause injuries to people or
 property.

1.1 Checking loose parts in the stove

After unpacking, check the following:
- The riddling grate (in the centre of the fire bed) and the fire bricks are firmly in position and
have not shifted during transit.
- The front grate is placed correctly
- The air control works smoothly.
- The strip of wood in the top of the radiation shield at the back of the stove should be
removed.

Standard Accessories
Poker, ceramic flue connection gasket and riddling tool are standard accessories, and can
usually be found in the ashpan or firebox area.

  1.0 Installation of your Morsø stove

 Installation of woodburning stoves must be safe and legal.

 If your Morsø stove is not installed correctly, it may cause a house fire. To reduce

 the risk of fire, the installation instructions must be followed carefully. Contact the

 local building officials about restrictions and installation inspection in your area.

Before you start installing your stove, make sure that:

- The stove and chimney connection are placed far enough from combustible materials to meet
all clearance requirements.
- The floor protection must be adequate and must be made correctly according to ´the
requirements.
All neccessary approvals are needed from the local building officials.

The data plate, which is located on the back of the stove, provides information regarding safety
testing information, name of certified testing laboratory, and installation requirements.

Содержание 4600 Series





















Отзывы: