background image

The Specialist In Drum Handling Equipment

Model 400A-72SS-117

Stainless Steel Hydra-Lift, 72”,  

AC Power Lift & Tilt

Operator’s Manual for Morse Hydra-Lift Karrier Model 400A-72SS-117

Serial Number 400000 to ______ 

morsedrum.com

Copyright 2022 - Morse Mfg. Co., Inc. 

Form OM400A-72SS-117 (400000-______)  

(Updated 26 Sep., 2022)

 

5

Operating Instructions

1.)  Push Hydra-Lift Karrier to drum.

 

2.)  Using “LIFT” control as described in “

Machine 

Description - Controls

”, position drum holder 

assembly with back band at middle of drum. (Figure 

3.1).  With ratchet plate swung open and cinch chain 

hanging from chain hook, push unit until back band 

rests firmly against drum.  Some adjustment to tilt angle 

of saddle may be necessary to ensure band fits flush on 

drum. 

3.) 

Attaching the drum:

Drape chain across front of drum and engage a link into 

notch in ratchet (Figure 3.2).  Turn ratchet clockwise to 

tighten chain.  If ratchet turns until pawl is beyond last 

ratchet tooth, turn ratchet back and slide next link into 

ratchet notch and try tightening again.  Chain must be 

held tightly against drum with pawl engaged securely in 

ratchet teeth. 

4.) Operate lift function to lift drum clear of floor.  Roll to 

dispensing location.  NOTE: Do not allow drum to impact 

on floor, pouring station, etc. or spill or damage could 

occur.

START-UP Procedure

Machine is shipped with hydraulic fluid. 

1.  Install provided hydraulic control levers (threaded 

rods with black ball handles).

 

2.  IMPORTANT:

 BEFORE operation, remove the 

RED

 shipping plug from the hydraulic reservoir, and 

replace with the provided 

BLACK

 breather.

CAUTION

 

– Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. 

 The 

unit can become unstable when transporting with a raised load.

5.) Lift drum to desired pouring height.  Operate the tilt control as described in 

“Machine Description - Controls”

 to 

adjust the drum attitude. This is especially important when lifting an open drum.  The floor lock should be engaged while 

dispensing / draining.

Figure 3.2

Содержание 400A-72SS-117







Отзывы: