background image

Page 2

MD38-DV-2  Homefire

Part No. XG0111

Introduction

About the M38 Series Modular Fireplaces:

The MD38-DV-2 includes a 27,000 BTU dual burner and embers. All
38 Series Modular Fireplaces allow quick and easy upgrades in the
future. The MD38-DV-2 can be upgraded to a Wildfire Burner. Contact
your dealer for more information. The MD38-DV-2 model is available in
four versions:

n

Top Vent (Product Code MD38DT-2)

n

Rear Vent (Product Code MD38DR-2)

n

Intermittent Pilot - Top Vent (Product Code MD38DT-I-2)

n

Intermittent Pilot - Rear Vent (Product Code MD38DR-I-2)

The MD38-DV-2 is rated for Natural Gas at 27,000 BTU/H (8.5
Kilowatts) Input or Propane at 27,000 BTU/H 8.5 Kilowatts) Input.

How to use this manual:

This manual covers all models and unless otherwise specified, the
designation MD38-DV-2 refers to all models. Sections which are
specific to a particular model are marked with a                symbol, plus
the appropriate model number.

Warranty and Installation Information:

The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:

n

Modification of the fireplace and/or components including Direct-
Vent assembly or glass doors.

n

Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.

n

Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done
by a qualified contractor.

Installations in Canada must conform to the current CAN/CGA B-
149.1
 and .2 Gas Installation Code and local regulations. If the
optional air-circulating fan kit is installed, it must be electrically
grounded in accordance with CSA C22.1 Canadian Electrical Code
Part 1 and/or Local Codes.

Installations in the USA must conform to local codes, or in the
absense of local codes to the National Fuel Gas Code, ANSI Z223.1-
1988
. If the optional air-circulating fan is installed, it must be
grounded in accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70-1987.

Table Of Contents

Introduction ............................................................................. 2

Installation

Installing the Fireplace Shell ......................................... 3

Installing the Gasline ..................................................... 4

The Remote Switch ....................................................... 4

Direct Vent Installation .................................................. 4

General Requirements ...................................... 4

Terminations ..................................................... 5

Top Vent Models with horizontal runs ............... 6

Top Vent Models with vertical runs ................... 8

Rear Vent Models ............................................. 9

Construction around the fireplace

Facing ............................................................. 10

Mantels and Surrounds ................................... 10

Wiring ................................................................ 10 - 11

Installing the Logset .................................................... 11

Removing and Installing the Insert .............................. 11

Removing and Installing the Door ............................... 11

Operation ........................................................................ 13 - 15

Maintenance ................................................................... 15 - 16

Warranty ................................................................................. 19

Appendix

A. Accessories ............................................................ 18

B. Termination Locations ............................................ 19

CAUTIONS

Due  to  its  high  operating  temperatures,  the  appliance
should  be located out of traffic & away from furniture and
draperies.

n

Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.

n

Young children should be carefully supervised when
they are in the same room as the appliance.

n

Clothing or other flammable materials should not be
placed on or near the appliance.

Содержание Homefire plus MD38-DV-2























Отзывы: