Montigo E38-PV Скачать руководство пользователя страница 1

Страница: 1 / 18

Check local codes and
read all instructions
prior to installation.

Leave this manual with
the owner.

Power-Vented

Gas Fireplace

E38-PV

Installation

Operation &

Maintenance

What To Do If You Smell Gas:

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

Warning:

Improper installation, adjustment,

alteration, service or maintenance can cause

injury or property damage. Refer to this

manual. For assistance or additional

information consult a qualified installer,

service agency or the gas supplier.

For Your Safety:

Do not store or use gasoline
or other flammable vapors
and liquids in the vicinity of
this or any other appliance.

Questions? Email us at [email protected] or visit our website at www.montigo.com.

Содержание E38-PV



















Результаты поиска

Содержание E38-PV

Отзывы:

Похожие инструкции для E38-PV

Бренды по названию

Популярные бренды

Montigo E38-PV, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание E38-PV

Отзывы:

Похожие инструкции для E38-PV

Бренды по названию

Популярные бренды