manualshive.com logo in svg

Montesa COTA 4RT 260 2020, Руководство пользователя

Поделиться
Скачать
Montesa COTA 4RT 260 2020 Скачать руководство пользователя страница 61

Install the fuel pump mounting bolts.

Tighten the fuel tank mounting bolts in the alphabetical 

order shown.

Torque: 7 - 9 N•m (0.7 - 0.9 kgf•m, 5.1 - 6.6 lbf•ft)

(1) FUEL PUMP

(2) BOLTS

Remove the 5P connector and fuel feed hose.

Remove the fuel pump base mounting bolts.

Remove the fule pump assembly being careful not to 

damage the pump.

(1) FUEL PUMP

Installation

NOTICE

Always replace the packing with a new one when the fuel 
pump is removed.

Clean any oil off from the mating surface of the fuel pump 

base and fuel tank.

Install a new packing onto the fuel pump base.

Install the fuel pump assembly into the fuel tank (as pic-

tures shows).

Be careful not to damage the fuel pump wire.

Make sure the packing is seated against the fuel tank.

Also check that the packing is not placed on the fuel tank 

boss.

(1) QUICK CONNECTOR   

(2) FUEL FEED HOSE

(3) 5P CONNECTOR

(1) FUEL PUMP

(2) BOLTS

Engine servicing

4-8

4-8

2

1

3

1

1

2

1

2

A

C

E

B

G

D

F

Содержание COTA 4RT 260 2020































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды