manualshive.com logo in svg

Montesa COTA 4RT 260 2020, Руководство пользователя

Поделиться
Скачать
Montesa COTA 4RT 260 2020 Скачать руководство пользователя страница 102

Remove the engine oil drain bolt and sealing washer, drain 

the engine oil.

Remove the bolts and left crankcase cover.

NOTE

The left crankcase cover (stator) is magnetically attached 
to the fl ywheel, be careful during removal.

Remove the left crankcase cover, gasket and dowel pins.

(1) DRAIN BOLT/SEALING WASHER

(2) BOLTS

(3) LEFT CRANKCASE COVER

 Left Crankcase Cover

Removal

Remove the skid plate and drain engine oil.

Disconnect the alternator 3P (Natural) connector and 

ignition pulse generator 2P (Natural) connectors.

Remove the gearshift pedal.

(1) 3P (NATURAL) CONNECTOR

(2) 2P (NATURAL) CONNECTOR

(1) GEARSHIFT PEDAL

Install the washer and gearshift spindle aligning the return 

spring ends with the shift fork shaft on the crankcase and 

guide plate hole with the shifter collar.

Install the gearshift pedal and check the operation.

(1) WASHER    

(2) GEARSHIFT SPINDLE

(3) RETURN SPRING PIN

(4) SHIFTER COLLAR

Engine servicing

4-49

4-49

4

3

2

1

2

1

3

2

1

1

Содержание COTA 4RT 260 2020































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды