manualshive.com logo in svg

Montesa COTA 4RT 260 2020, Руководство пользователя

Поделиться
Скачать
Montesa COTA 4RT 260 2020 Скачать руководство пользователя страница 104

(1) DOWEL PINS   

(2) NEW GASKET

 Installation

Check the oil filter cover O-ring is in groove condition, 

replace if necessary.

Install dowel pins and new gasket.

(1) OIL FILTER COVER

(2) O-RING

(1) STATOR   

(2) IGNITION PULSE GENERATOR

(3) WIRE CLAMP   

(4) SOCKET BOLTS

(5) BOLTS   

(6) GROMMET

Install the stator and ignition pulse generator assembly 

into the left crankcase cover.

Apply locking agent to the stator and ignition pulse 

generator mounting bolt threads.

Install the alternator wire clamp.

Install the stator and ignition pulse generator mounting 

bolts.

Tighten the stator mounting bolts to the specified torque.

Torque: 5.4 N•m (0.55 kgf•m, 4.0 lbf•ft)

Tighten the ignition pulse generator mounting bolts to the 

specified torque.

Torque: 5.4 N•m (0.55 kgf•m, 4.0 lbf•ft)

Apply sealant to the stator/ignition pulse generator wire 

grommet and install it into the left crankcase cover groove.

(1) OIL SEAL

(2) WASHER

(3) SNAP RING

Apply grease to the new oil seal lip and install it into the 

left crankcase cover.

Install the washer and snap ring.

Install the oil pressure relief valve (page 4-1).

Engine servicing

4-51

4-51

1

4

3

2

5

5

1

2

3

6

2

1

2

1

1

Содержание COTA 4RT 260 2020































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды