© 2013 Monte Carlo Fan Company
6/25/2013
8
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate
when switch is in the middle.
4.Make sure that shipping stabilizer tabs have been removed from motor (see installation
step #13).
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glass-
ware are finger tight. Check to be sure light bulb is tight in socket and not touching glass
shade(s). If vibration persists from glass, remove glass and install a 1/4" wide rubber band
on glass neck to act as an insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed controls.
DO
NOT USE a Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the
notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box
and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance from
blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-
tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can ad-
just blade levels by the following procedure. To adjust a blade tip down, insert a washer (not
supplied) between the blade and blade holder at the screw closest to the motor. To adjust a
blade tip up, insert washer (not supplied) between the blade and blade holder at the two
screws farthest from the motor. Reverse the position of the washer if blades mount from top
of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can re-
distribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION:
Make sure main power is turned off before entering switch housing.
WARNING:
Over lamping the fan will result in the fan lights shutting down until the
proper wattage of bulbs are installed.
Reset the lights by turning off the wall switch, breaker,or by remote. Replace bulbs with the
correct wattage bulbs, turn the power on.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
T
ROUBLe
S
HOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installa-
tion, please call our Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service discon-
necting means to prevent power from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Trouble
Suggested Remedy
