background image

7

© 2021 Monte Carlo Fan Collections

8/2021

Remote Controller Operation

Remove the battery cover from the remote control transmitter and install batteries. 

Replace the cover. This remote uses 2 1.5V/AAA batteries.

Note

: If not using for long periods of time, remove the batteries to prevent damage to 

remote controller, and store the remote controller away from excess heat or humidity. 

The batteries will weaken with age and should be replaced before they leak or corrode as 

this will damage the controller. Dispose of the used batteries properly. Always keep 

batteries out of the reach of children.  

Dimming, Non Dimming Setting (Only available for fans with light) 

In the dimming mold, it is a light dimming selection and it is to be used with dimmable 

luminaries. The remote controller is set with dimming function at factory. 

In ON/OFF (non-dimming mold), it is for light ON/OFF only (non-dimming function).

  

The remote control buttons control the fan speed as follows:

1 = minimum speed          2 = low speed      3 = medium low speed     

4 = medium speed         5 = medium high speed       6 = high speed

      

This button turns the fan off.

      

Forward

/

Reverse button: This button is to control direction of fan rotation. Press once

     to change direction of the fan rotation. Fan must be running to reverse.        
     Light button- Press this button to turn light on or off.
     Light button- Press this button to desired brightness, dim to bright.
     Light button- Press this button to desired brightness, bright to dim.
     Breeze: 
Press the Breeze button, fan will operates randomly among minimum, low and medium low speed at 

intervals of 30 seconds until the breeze mold is canceled.
Breeze mode can be erased by pressing either the power or speed control buttons.  

Note

: This remote controller has auto resume function. The fan will maintain the last setting when 

turned back on, with the exception of Breeze mode.

Battery cover

DIM (D)

ON/OFF (O)

SET

SET

1

0

1

0

1

0

Universal Mode and Learning Mode

Your remote controller has two options: “Universal Mode” (mark “0”) and “Learning Mode” (mark “1”). 
If choosing “Universal Mode,” simply move the switch to the LOWER position (mark “0”). Your fan with 

the remote controller is ready to use.

Note

: If using Universal Mode, your fan can be controlled with other remote controllers with the same 

setting.
To control the fan with a specific remote controller, choose “Learning Mode” by moving the switch to 

the UPPER position (mark “1”) and then follow the Learn Mode steps below.

Learn Mode
Important

: Turn the power on for ONLY the specific fan you wish to pair with the remote controller. 

Make sure to turn the power off for all other fans with which you use the same remote controller.
Restore power to your fan, press and hold the “SET” button to pair the transmitter and receiver. You 

must press the ‘SET” button within 60 seconds of restoring power to the fan.

Note

: Fan will at first operate at minimum speed and light will blink (if your fan has a light) after you’ve 

chosen Learn Mode.

Note

: If the power is already on, you must turn the power off and then back on for the remote control 

setting.

Note

: If you reset the controller to Universal Mode (mark “0”) and later want to pair the controller 

again to a specific fan, you have to repeat the Learn Mode steps.

 

Содержание 3STMSM60 Series












Отзывы: